Edit Section
56
(Continued from previous page)
4 C o m p l e t e l y S e p a r a t e E f f e c t s
If you specifically set the output of each drum voice,
system effects and two insertion effects can be used as
four completely separate effects. Here is a example of
applying four different effects to four separate drum
voices and sending the signals to the stereo OUTPUT
jacks:
Settings in the [Voice6] page...
• For drum voice 1: Output = stereo, RevSend = (other
than zero), ChoSend = 0
• For drum voice 2: Output = stereo, RevSend = 0,
ChoSend = (other than zero)
• For drum voice 3: Output = InsFX1
• For drum voice 4: Output = InsFX2
Effect settings:
• In the [Effect] page (master send levels to system reverb
and chorus effects): Localizer = off, RevSend = (other
than zero), ChoSend = (other than zero)
• In the [Reverb] page (master return level from system
reverb effect): RevRetrn = (other than zero)
• In the [Chorus] page (master return level from system
chorus effect): Cho
➝
Rev = 0, ChoRetrn = (other than
zero)
• In the [InsFX] pages: Type = (other than THRU) for FX
= 1, and RevSend = 0 (zero), ChoSend = 0, Output =
stereo
• In the [InsFX] pages: Type = (other than THRU) for FX
= 2, and RevSend = 0, ChoSend = 0, Output = stereo
If you make four one-on-one routes (from voice to
effect) and select a different effect (also different from
system reverb and chorus effects) for each insertion
effect, you can output each drum voice in stereo, each
with a different effect applied.
P a r a l l e l O u t p u t s w i t h E f f e c t s
You can easily send a drum voice to the
INDIVIDUAL OUTPUT jacks if you set Output to
IND (in stereo pair or mono) in the voice settings.
However, these settings only allow dry outputs of
drum voices without any effects applied. You can also
utilize insertion effects for parallel outputs of drum
voices while applying your favorite effects.
Settings in the [Voice6] page...
• Output = InsFX1 — for snare drum
• Output = InsFX2 — for bass drum
• Output = IND3&4 — for tom 1
• Output = IND3&4 — for tom 2
• Output = IND5&6 — for tom 3
• Output = IND5&6 — for tom 4
• Output = stereo, RevSend = (any value), ChoSend = (any
value) — for cymbals
Effect settings:
• In the [Effect] page (master send levels to system reverb
and chorus effects): Localizer = off, RevSend = (other
than zero), ChoSend = (other than zero)
• In the [Reverb] page (master return level from system
reverb effect): RevRetrn = (other than zero)
• In the [Chorus] page (master return level from system
chorus effect): Cho
➝
Rev = (any value), ChoRetrn =
(other than zero)
• In the [InsFX] pages: Type = 2BandEQ for FX = 1, and
RevSend = 0, ChoSend = 0, Output = IND1
• In the [InsFX] pages: Type = COMP for FX = 2, and
RevSend = 0, ChoSend = 0, Output = IND2
With these settings, you can obtain the following
results. Note that you can even count and use the
stereo OUTPUT jacks as a pair of INDIVIDUAL
OUTPUT jacks.
• Snare drum: Mono output from INDIVIDUAL
OUTPUT 1 without system reverb and chorus effects,
after processing with two-band equalizer from insertion
effect 1.
• Bass drum: Mono output from INDIVIDUAL
OUTPUT 2, after processing with compressor from
insertion effect 2.
• Toms 1 and 2: Stereo output from INDIVIDUAL
OUTPUT 3 and 4 without any effects applied.
• Toms 3 and 4: Stereo output from INDIVIDUAL
OUTPUT 5 and 6 without any effects applied.
• Cymbals: Stereo output from OUTPUT (L/MONO and
R) with system reverb and chorus effects applied.
In these examples, the output signal routing and effect
settings are closely associated. Try out other signal
routings for your specific applications and
requirements.