7-4
FUEL INJECTION SYSTEM
FI
EAS00902
ALTERNATE INSTRUCTIONS OPERATION CONTROL (FAIL-SAFE ACTION)
If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illumi-
nates the engine trouble warning light and provides the engine with alternate operating instructions
that are appropriate for the type of malfunction.
When an abnormal signal is received from a sensor, the ECU processes the specified values that are
programmed for each sensor in order to provide the engine with alternate operating instructions that
enable the engine to continue to operate or stop operating, depending on the conditions.
The ECU takes fail-safe actions in two ways: one in which the sensor output is set to a prescribed value,
and the other in which the ECU directly operates an actuator. Details on the fail-safe actions are given
in the table below.
FAIL-SAFE ACTIONS TABLE
Fault
Code No.
Item
Symptom
Fail-safe action
Engine
startability
Vehicle
drivability
12
Crankshaft position
sensor
No normal signals are received from
the crankshaft position sensor.
S
Stops the engine (by stopping the
injection and ignition).
Unable
Unable
13
14
Intake air pressure
sensor (open or short
circuit) (pipe system)
Intake air pressure sensor-open or
short circuit detected.
Faulty intake air pressure sensor pipe
system.
S
Fixes the intake air pressure to
101.3 kpa.
Able
Able
15
16
Throttle position sensor
(open or short circuit)
(stuck)
Throttle position sensor-open or short
circuit detected.
A stuck throttle position sensor is
detected.
S
Fixes the throttle position sensor to
fully open.
Able
Able
19
Sidestand switch (open
circuit in wire to ECU)
Open circuit in the input line of ECU
No.4 terminal is detected when the start
switch is pressed.
-- (No start)
Unable
Unable
21
Coolant temperature
sensor
Coolant temperature sensor-open or
short circuit detected.
S
Fixes the coolant temperature to
60
_
C.
Able
Able
22
Intake temperature
sensor
Intake temperature sensor-open or
short circuit detected.
S
Fixes the intake temperature to 20
_
C.
Able
Able
33
Faulty ignition
Open circuit detected in the primary
lead of the ignition coil. (#1, #4)
S
Cut the injection of other cylinder in
the same group with the cylinder that
the error is detected. (Example: when
the #1 cylinder is defective cut the in-
Able
(depending
on the num
Able
(depending
on the num
34
Open circuit detected in the primary
lead of the ignition coil. (#2, #3)
the #1 cylinder is defective cut the in-
jection of #1 and #4 cylinders)
S
Turn on the power to the air induction
solenoid to always cut-off the air.
on the num-
ber of faulty
cylinders)
on the num-
ber of faulty
cylinders)
30
41
Lean angle cut-off
switch (latch up
detected) (open or short
circuit)
The motorcycle has over turned.
Lean angle cut-off switch-open or short
circuit detected.
S
Turns OFF the fuel injection system
relay of the fuel system.
Unable
Unable
42
Speed sensor, neutral
switch
No normal signals are received from the
speed sensor; or, an open or short
circuit is detected in the neutral switch.
S
Fixes the gear to the top gear.
Able
Able
43
Fuel system voltage
(monitor voltage)
Supply power to the injector and fuel
pump is not normal.
S
Fixes the battery voltage to 12 V.
Depending
on the mal-
function
case.
Depending
on the mal-
function
case.
44
Error in writing the
amount of CO
adjustment on
EEPROM
An error is detected while reading or
writing on EEPROM (CO adjustment
value).
--
Able
Able
46
Vehicle system power
supply (Monitor voltage)
Power supply to the FI system not
normal
--
Able
Able
50
ECU internal
malfunction (memory
check error)
Faulty ECU memory. When this
malfunction is detected, the code
number might not appear on the meter.
S
Shut down all functions except the
communication with the meter.
Unable
Unable
—
Start unable warning
Relay is not turned ON even if the crank
signal is input while the start switch is
turned ON. When the start switch is
turned ON while an error is detected
with the fault code of No.12, 19, 30, 41,
43 or 50.
Engine trouble warning light flashes
when the start switch is turned ON.
Unable
Unable
Summary of Contents for FZ6-SS
