E
-31
English
Recording
■
Manual EDIT recording
You can program tracks manually while watching the remaining
time on both sides of the tape.
1
Press
INPUT
or
repeatedly until “VCD/CD” (
1
) appears
on the display, and load a disc (or discs) on the disc tray.
2
Follow steps 3–5 on page 30.
3
Press
PROG
.
* “PROG” and “P-01” will light up on the display, and all track
numbers on the selected disc will begin blinking.
4
If necessary, select the desired disc by pressing
DISC SKIP
.
5
Select the desired track number by pressing the numeric buttons.
6
Repeat steps 4 and 5 to program more selections for side A of
the tape. You can select the same track again.
* Pressing
TIME
displays the total remaining time on side A of
the tape for about 1 second, and then it is replaced by the
display of the next play order.
* You can only select track numbers 1 through 15 for manual
EDIT recording. All track numbers higher than 15 i.e.16, 17,
18… cannot be selected for recording even if there is
recordable space available on the tape.
“TM OVER” will appear on the display.
At this time, however, if any other track number is flashing
continuously on the display, you can program it instead of the
unprogrammable one.
7
When the programming for side A is finished, press
R. TIME
.
* “Side–B” appears on the display. You can begin programming
for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing
R.
TIME
at any time before you press
EDIT
in step 9.
* The tape side indicator (
9
) shows the programming side
currently selected.
8
Repeat steps 4 and 5 to program selections for side B of the tape.
You can select the same track again.
9
Press
EDIT
. (“EDIT” (
8
) lights up on the display.)
The recording begins.
Note
To check, cancel or correct program data, refer to page 16.
To cancel the EDIT function
Before recording, press on the CD/Video CD player or the
tape deck.
To stop recording
Press on the tape deck.
(At this time, disc play automatically stops.)
Notes on recording with the EDIT function
• The maximum number of tracks that can be programmed is 20.
• The track number 16 or higher cannot be programmed by this function.
• The CD/Video CD player’s repeat play mode will be canceled during
this recording mode.
Display information during programming
STANDBY
/ON
STANDBY
TIMER
PROGRAM
B.BOOST
MUSIC
INPUT
PRESET/TUNING/BAND
A/B/C/D/E
/
VOLUME
UP
DOWN
DIRECTION
PHONES
BASS
TREBLE
MODE
DOLBY NR
REC/
PAUSE
AUTO/
MANUAL
TIMER
MEMORY
TIME ADJ
RANDOM
HOUR
REPEAT
TIME
DISPLAY
MIN
1
TIME
PROG
V
A
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
CD
NR
PROG
V
A
OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
REM
TRACK
CD
NR
Programmed track numbers light up and
only programmable track numbers
among unprogrammed ones flash.
Selected track
number
Total remaining time on
this side of the tape
Selected disc
Next play order
Side of the tape
POWER
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
0
PRESET
TUNER
+I0
PRESET
TIME
A
PROG
B
R.TIME
C
EDIT
D
DISC SKIP
INTRO
MODE
RETURN
SELECT
E
KARAOKE
TIME INDEX
DIGEST
TIME INDEX
VCD/CD
/
DIRECTION
LEVEL
REC/ PAUSE
TEST
—
PROGRAM
CENTER/
REAR/ DELAY
KEY/ECHO
MUSIC
SLEEP
INPUT
TAPE
VOLUME
1
4
3
7
9
TIME
5
