PREPARATIONS
➤
Connecting speakers
En
16
■
Connecting speaker cables
Speaker cables have two wires. One is for connecting
the negative (-) terminal of the unit and the speaker, and
the other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive terminal.
a
Remove approximately 10 mm (3/8”) of insulation from
the ends of the speaker cable and twist the bare wires of
the cable firmly together.
b
Loosen the speaker terminal.
c
Insert the bare wires of the cable into the gap on the side
(upper right or bottom left) of the terminal.
d
Tighten the terminal.
Using a banana plug
(U.S.A. and China models only)
a
Tighten the speaker terminal.
b
Insert a banana plug into the end of the terminal.
■
Connecting the subwoofer
Use an audio pin cable to connect the subwoofer.
Connecting front speakers that
support bi-amp connections
(HTR-5065 only)
When using front speakers that support bi-amp
connections, connect them to the FRONT jacks and
SURROUND BACK/BI-AMP/ZONE B jacks.
To enable the bi-amp function, set “Power Amp Assign”
(p.69) in the “Setup” menu to “BI-AMP” after connecting
the power cable to an AC wall outlet.
Connecting Zone B speakers
(HTR-5065 only)
The Zone A/B function allows you to playback an input
source in the room where the unit is installed (Zone A)
and in another room (Zone B). To connect the Zone B
speakers, see “Playing back music in multiple rooms
(HTR-5065 only)” (p.60).
FR
ONT
a
a
b
d
c
+ (red)
- (black)
FRO
NT
a
b
Banana plug
SUBWOOFER
AUDIO
MONITO
R OUT
Y
AV
OUT
AV6
Audio pin cable
1
2
3
4
5
9
FRONT
CENTER
SURROUND
SINGLE
SURROUND BACK/BI AMP
/ZONE B
SPEAKERS
The unit (rear)
Caution
• Before making bi-amp connections, remove any brackets or
cables that connect a woofer with a tweeter. Refer to the
instruction manual of the speakers for details. If you are not
making bi-amp connections, make sure that the brackets or
cables are connected before connecting the speaker cables.
• Surround back speakers cannot be used during bi-amp
connections.
1 2
Speaker connections
3 4 5 6 7 8 9 10
Summary of Contents for HTR-5065
