E-2
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1.
This unit is a sophisticated mini disc recorder. To ensure
proper operation for the best possible performance, please
read this manual carefully.
2.
Install your unit in a cool, dry, clean place with good
ventilation. Avoid placing it in direct sunlight, near
sources of heat, or in locations subject to vibration,
excessive dust, heat, cold, or moisture. To avoid humming
sounds, position the unit away from other electrical
appliances, motors, and transformers.
3.
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4.
Do not place another component on top of this unit, to do
so may discolor or damage the surface of the unit.
5.
Do not open the cabinet of this unit, to do so may result in
damage to the unit or electrical shock. If any foreign object
or substance gets into the unit, contact your dealer for
assistance.
6.
When removing the power plug from the wall outlet,
always pull directly on the plug; never pull the cord itself.
7.
Do not apply excessive force when operating switches and
knobs.
8.
When moving the unit, be sure to first disconnect the
power cord from the AC outlet and disconnect all cords
connecting the unit to other equipment.
9.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
10.
Do not attempt to clean this unit with chemical solvents as
this may damage the finish. Use a clean, dry cloth.
11.
Be sure to read the “TROUBLESHOOTING” section for
advice on common operating errors before concluding that
your unit is faulty.
12.
Keep this manual in a safe place for future reference.
13.
The voltage to be used must be the same as that specified
on this unit. Using this unit with a higher voltage than that
which is specified is dangerous and may result in a fire or
other type of accident causing damage. YAMAHA will not
be held responsible for any damage resulting from use of
this unit with a voltage other than that which is specified.
Note
Please check the copyright laws in your country to record
from records, compact discs, radio, etc. Recording of
copyright material may infringe copyright laws.
This mini disc recorder is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the rear exterior.
(U.K., Europe and general
models only)
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off
and an appropriate 3 pin plug fitted. For details, refer to
the instructions described below.
Note:
The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is
hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured
BLUE must be connected to the terminal which is
marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected
to the terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the
earth terminal of the three pin plug.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove a disc from the unit,
press POWER to turn the unit off, then disconnect the AC
power plug from the wall outlet.
WARNING
To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
DANGER
Invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Voltage Selector <General model only>
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC power supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
