background image

1.  IMPORTANT NOTICE: DO NOT MOD-

IFY THIS UNIT!

This product, when installed as indicated 
in the instructions contained in this man-
ual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha 
may void your authority, granted by the 
FCC, to use the product.

2. IMPORTANT:

 When connecting this 

product to accessories and/or another 
product use only high quality shielded 
cables. Cable/s supplied with this prod-
uct MUST be used. Follow all installation 
instructions. Failure to follow instructions 
could void your FCC authorization to use 
this product in the USA.

3. NOTE:

 This product has been tested 

and found to comply with the require-
ments listed in FCC Regulations, Part 15 
for Class “B” digital devices. Compliance 
with these requirements provides a rea-
sonable level of assurance that your use 
of this product in a residential environ-
ment will not result in harmful interfer-
ence with other electronic devices. This 
equipment generates/uses radio fre-
quencies and, if not installed and used 
according to the instructions found in the 
users manual, may cause interference 

harmful to the operation of other elec-
tronic devices. Compliance with FCC 
regulations does not guarantee that 
interference will not occur in all installa-
tions. If this product is found to be the 
source of interference, which can be 
determined by turning the unit “OFF” 
and “ON”, please try to eliminate the 
problem by using one of the following 
measures:

Relocate either this product or the 
device that is being affected by the inter-
ference. 

Utilize power outlets that are on different 
branch (circuit breaker or fuse) circuits 
or install AC line filter/s.

In the case of radio or TV interference, 
relocate/reorient the antenna. If the 
antenna lead-in is 300 ohm ribbon lead, 
change the lead-in to co-axial type 
cable.

If these corrective measures do not pro-
duce satisfactory results, please contact 
the local retailer authorized to distribute 
this type of product. If you can not locate 
the appropriate retailer, please contact 
Yamaha Corporation of America, Elec-
tronic Service Division, 6600 Orangetho-
rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corpora-
tion of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

FCC INFORMATION (U.S.A.)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Summary of Contents for ME02R96










Reviews: