V
oice mode
P
erf
ormance
mode
Song mode
Utility mode
File mode
Master mode
P
attern mode
Mixing V
oice
mode
Ref
erence
Voice Edit mode
Normal Voice Edit Element Edit
160
Owner’s Manual
EGTimeSens
(EG Time Sensitivity)
Determines the degree to which the notes (specifically, their position or octave range) affect the Pitch EG times
of the selected Element. The Center Key (next parameter) is used as the basic pitch for this parameter. A
positive setting will cause the amplitude of lower notes to change slower and that of higher notes to change
faster. conversely, negative values will cause it to fall.
Settings:
-64 – 0 – +63
F
CenterKey
Determines the central note or pitch for the Key Follow effect on Pitch EG. When the Center Key note is played,
the PEG behaves according to its actual settings. The pitch change characteristics for other notes will vary in
proportion to the EG Time settings.
Settings:
C -2 – G8
n
You can also set the Center Key directly from the keyboard, by holding down the [INFORMATION] button and pressing
the desired key.
[F3] FILTER
[SF1] TYPE
From this display you can make comprehensive settings for the Filter unit. The available parameters differ
depending on which Filter type is selected here.
Type
Basically, there are four different Filter types: an LPF (Low Pass Filter), an HPF (High Pass Filter), a BPF (Band
Pass Filter) and a BEF (Band Elimination Filter). Each type has a different frequency response and produces a
different effect on the sound. This synthesizer also features special combination Filter types, for additional
sonic control.
Settings:
Gain
Determines the Gain (the amount of boost applied to the signal sent to the Filter).
Settings:
0 – 255
Cutoff
Determines the cutoff frequency for the Filter. or the central frequency around which the Filter is applied.
Settings:
0 – 255
Resonance/Width
This parameter’s function varies according to the selected Filter Type. If the selected filter is an LPF, HPF, BPF
(excluding the BPFw), or BEF, this parameter is used to set the Resonance. For the BPFw, it is used to adjust the
Width of the band. Resonance is used to set the amount of Resonance (harmonic emphasis) applied to the signal
at the cutoff frequency. This can be used in combination with the cutoff frequency parameter to add further
character to the sound. The Width parameter is used to adjust the width of the band of signal frequencies passed
by the filter with the BPFw.
Settings:
0 – 127
Distance
Determines the distance between the Cutoff frequencies, for the Dual Filter types (which feature two identical
filters combined in parallel, and the LPF12 + BPF6 type).
Settings:
0 – 255
HPFCutoff
Determines the central frequency for the Key Follow parameter (below) of the HPF. When a filter type “LPF12”
or “LPF6” is selected, this parameter is available.
Settings:
0 – 255
HPFKeyFlw (Key Follow)
Determines the Key Follow setting for the HPF Cutoff frequency. This parameter varies the center frequency
according to the position of the notes played on the keyboard. A positive setting will raise the center frequency
for higher notes and lower it for lower notes. A negative setting will have the opposite effect. This parameter is
available only when the filter type “LPF12” or “LPF6” is selected.
Settings:
-200 ~ 0 ~ +200
[SF2] VEL SENS
(Velocity Sensitivity)
From this display you can determine how the Filter and the FEG respond to velocity.
EGTime,
Segment
Determines the velocity sensitivity of the FEG’s Time parameters.
Select the Segment first, then set its Time parameter. Positive Time settings will play back the specified
Segment faster in proportion to the played velocity and negative values will play it back slower.
Settings:
EG Time: -64 – 0 – +63
Settings:
Segment: atk, atk+dcy, dcy, atk+rls, all
atk (attack) .............................EG Time Value affects Attack time.
atk+dcy ( decay) ......EG Time Value affects Attack/Decay1 time.
dcy (decay)............................EG Time Value affects Decay time.
atk+rls ( release).......EG Time Value affects Attack/Release time.
all ..........................................EG Time Value affects all FEG Time parameters.
Center key
Center key
Higher
range
Lower
range
Large
Small
–
+
Amount of
pitch change
Positive value
Higher range
Lower range
Slower speed
Faster speed
+63
+30
-40
Negative value
When Pitch Sensitivity is set to 100
Pitch Sensitivity and Center Key
EG Time Sensitivity and Center Key
Summary of Contents for MO6
Page 1: ...OWNER S MANUAL MUSIC PRODUCTION SYNTHESIZER EN...
Page 236: ...236 Owner s Manual Memo...
Page 237: ...237 Owner s Manual Memo...
Page 238: ...238 Owner s Manual Memo...
