Yamaha MO6 Owner'S Manual Download

Page: 206 / 240

oice mode

erf
ormance

mode

Song mode

Utility mode

File mode

Master mode

attern mode

Mixing V

oice

mode

Ref

erence

Utility mode

206

Owner’s Manual

[SF4] OTHER

AutoLoad

Determines whether the Auto Load function is on or off. When this is on, the instrument will automatically load
the specified files (from USB storage device) to User memory—whenever the power is turned on. For details
about the Auto Load function, see page 102.

Settings:

on, off

PowerOnMode

This determines the default power-on mode (and memory bank)—letting you select which condition is
automatically called up when you turn the power on.

Settings:

performance, voice (USR1), voice (PRE1), GM, last, master

performance ....Performance Play mode (User Performance 001)
voice (USR1)....Voice Play mode (User Voice “USR1: 001”)
voice (PRE1) ....Voice Play mode (Preset Voice “PRE 1: 001”)
GM ...................Voice Play mode (GM Voices “GM: 001”)
last ...................The mode and program number registered the last time by the procedure on page 210.
master ..............Master Play mode (User Master 001)

CtrlReset (Controller Reset)

Determines the status of the controllers (Modulation Wheel, Aftertouch, Foot Controller, Breath Controller,
Knobs, etc.) when switching between voices. When this is set to “hold,” the controllers are kept at the current
setting. When this is set to “reset,” the controllers are reset to the default states (below).

Settings:

reset, hold

If you select “reset,” the controllers will be reset to the following states/positions:
Pitch Bend .................... Center
Modulation Wheel ......... Minimum
Aftertouch .................... Minimum
Foot Controller  ............. Maximum
Breath Controller  .......... Maximum
Foot Switch  .................. Off
Expression ................... Maximum
Foot Volume  ................. Maximum
Sustain ......................... Off

[F2] OUTPUT

L&RGain

Set the output gain of the L/MONO and R jacks.

Settings:

0dB, +6dB

[F3] VOICE

[VOICE]

➞

[UTILITY]

➞

[F3]

These special voice-related settings are available only when entering the Utility mode from the Voice mode, letting you set parameters related to all the
Voices.

[SF1] MEQ (Master EQ)

From this display you can apply five-band equalization to all Voices, raising or lowering the level of each
frequency band (LOW, LOWMID, MID, HIGHMID, HIGH).
The parameters are the same as in the Performance Common Edit. See page 172.

Settings:

For details about EQ, see page 141.

[SF2] MEF (Master Effect)

From this display you can set the Master Effect related parameters applied to all the Voices. The parameters
are the same as in the Performance Common Edit. See page 172.

[SF3] ARP CH
(Arpeggio Channel)

From this display you can set parameters related to output of the Arpeggio MIDI data in the Voice mode.

OutputSwitch

This enables or disables MIDI data output for the Arpeggio function. When this is set to “on,” Arpeggio data is
sent via MIDI—allowing you to send the Arpeggio data to an external sequencer or play back the Arpeggios on
connected MIDI tone generators.

Settings:

on (enable), off (disable)

TransmitCh (Transmit channel)

Determines the MIDI channel through which Arpeggio playback data will be sent (when Output Switch above is
on).

Settings:

1 – 16

[SF4] CTL ASN
(Controller Assign)

Sets the parameters related to the controllers in the Voice mode. Details on each parameter are the same as in
Performance Common Edit. See page 173.

[F3] SEQ (Sequencer)

[SONG] or [PATTERN]

➞

[UTILITY]

➞

[F3]

These special song- and pattern-related settings are available only when entering the Utility mode from the Song or Pattern mode.

[SF1] CLICK

From this display you can set the parameters related to the click sound (metronome) that is used during
recording or playback in the Song/Pattern mode.

Mode

Determines whether and when the metronome click will sound.

Settings:

off, rec, rec/play, all

off .....................The click will not sound.
rec ....................The click will sound during song/pattern recording only.
rec/play ............The click will sound during song/pattern recording and playback.
all .....................The click will always sound.

Beat

Determines on which beats the metronome click will sound.

Settings:

16 (16th notes), 08 (8th notes), 04 (quarter notes), 02 (half notes), 01 (whole notes)

Volume

Determines the click sound volume.

Settings:

0 – 127

Type

Determines the click sound type.

Settings:

1 – 10