60
MONTAGE6/MONTAGE7
LCD display
Test items and judging conditions
09 : PB, MW, RB
Checks whether the Pitch Bend wheel, Modulation wheel and Ribbon controller work properly or not.
1) Press the [ENTER] button, and the target value “
<127>
” of each wheel and the target value “
<0>
”
of Ribbon controller are shown on the LCD.
There is no specific order for these items to be checked.
Pitch Bend
2) The target value “
<127>
” and the current value “
64
” are shown on the LCD.
* When starting this test, check to ensure that the Pitch Bend wheel is at the Center position. If it is
not at the Center position, “
Pitch Bend NG
” is shown. While “NG” is on the display, even if the
Pitch Bend wheel is moved, “NG” remains displayed.
3) Move the Pitch Bend wheel to the upper maximum position (127) according to the display of the
LCD.
Check the current value increases from 64 to 127 smoothly.
When 121 to 127 of the current value is detected, the displayed target value changes to “
<0>
”.
4) Move the Pitch Bend wheel to the lower minimum position (0) according to the display of the LCD.
Check the current value reduces from 127 to 0 smoothly.
When 0 to 6 of the current value is detected, the displayed target value changes to “
<64>
”.
5) Return the Pitch Bend wheel to the Center position (64) according to the display of the LCD.
Check the current value increases from 0 to 64 smoothly.
When 62 to 65 of the current value is detected, “
OK
” is shown on the LCD.
Modulation
6) The target value “
<127>
” is shown on the LCD.
7) Move the Modulation wheel to the upper maximum position (127) according to the display on the
LCD.
Check the current value increases from 0 to 127 smoothly.
When 126 to 127 of the current value is detected, the displayed target value changes to “
<0>
”.
8) Move the Modulation wheel to the lower minimum position (0).
Check the current value reduces from 127 to 0 smoothly.
When 0 to 1 of the current value is detected, “
OK
” is shown on the LCD.
Ribbon
9) The target value “
<0>
” is shown on the LCD.
10) Touch the left end of the Ribbon Controller which is the target value (0) with a finger according to
the display of the LCD.
When 0 to 19 of the current value is detected, the displayed target value changes to “
<100>
”.
11) Slide slowly rightward to the target value (100) according to the display on the LCD.
When 94 to 114 of the current value is detected, the displayed target value changes to “
<127>
”.
12) Slide slowly rightward to the target value (127) according to the display on the LCD.
When 115 to 127 of the current value is detected, “
OK
” is shown on the LCD.
When all checks resulted in “
OK
”, testing is finished and the display is changed to the test item
selection screen.
Note:
When the [EXIT] button is pressed during this test, the display is changed to the test item selec-
tion screen.
Pitch Bend wheel
Modulation wheel
Ribbon
controller
Summary of Contents for Montage 6
