70
MONTAGE6/MONTAGE7
LCD display
Test items and judging conditions
33 : Panel L Check (SW,
LED)
Checks whether switches and LEDs on the PNL circuit board work properly or not.
1)
Press the [ENTER] button, and “
Press AD INPUT ON/OFF / LED=ORANGE
” is shown on the
LCD.
2) Press the applicable button, and a sine wave sound is produced while the button is pressed. If the
button has LED, it lights up.
Note:
If a wrong button one is pressed, “
NG
” is shown and no sound is produced.
3)
Release the button, and the display changes to “
Press xxx / LED=xxx
(button name to be pressed
next)”.
4) Check buttons on the panel one after another in the specified order.
For the order to check switches, refer to page 73.
If there are a multiple number of applicable LEDs, press the same button by that number of times to
have each LED lit.
Press the [AD INPUT ON/OFF] button twice.
Press the [MULTI] button 7 times.
(Basically this is a Panel L switch test, but the panel R switch test is partially included.)
5)
When pressing all buttons is completed, “
OK
” is shown on the LCD.
6)
When OK of the test result is shown, testing is over and the display is changed to the test item
selection screen.
34 : Panel R Check (SW,
LED)
Checks whether switches and LEDs on the PNR circuit board work properly or not.
1)
Press the [ENTER] button, and “
Press DEC/NO / LED= - - -
” is shown on the LCD.
2) Press the applicable button, and a sine wave sound is produced while the button is pressed. If the
button has LED, it lights up.
Note:
If a wrong button is pressed, “
NG
” is shown and no sound is produced.
3)
Release the button, and the display changes to “
Press xxx / LED=xxx
(button name to be pressed
next)”.
4) Check buttons on the panel one after another in the specified order.
For the order to check switches, refer to page 74.
5)
When pressing all buttons is completed, “
OK
” is shown on the LCD.
6)
When OK of the test result is shown, testing is over and the display is changed to the test item
selection screen.
35 : Panel L Check (LED)
Checks that there is no problem with a set of panel LEDs which light up continuously.
1)
Press the [ENTER] button, and “
ON
” is shown on the LCD and the Knob LEDs and Slider LEDs
repeat the following operations respectively at the same time.
2)
Confirm that all LEDs flash in the correct order.
3)
Press the [EXIT] button, and testing is finished and the display is changed to the test item selection
screen.
Knob 1–9 :
1)
The LEDs of Knob 1 to Knob 4 turn on and off at the same time one by one in the clockwise direc
-
tion.
2)
The LEDs of Knob 5 to Knob 8 turn on and off at the same time one by one in the clockwise direc
-
tion.
3)
The LEDs of Knob 9 turn on and off one by one in the clockwise direction.
4)
All the LEDs of each knob turn on and off one after another. (With Knob 9, all LEDs of the left half
turn on and then all LEDs of the right half turn on.)
5) The same operation is repeated item 1) to item 4).
Slider 1–8 :
1)
The LEDs in rows from Slider 1 to Slider 4 turn on and off at the same time from the bottom up
-
ward as if they flow.
Summary of Contents for Montage 6
