4-61
REAR SHOCK ABSORBER ASSEMBLY
EAS23180
HANDLING THE REAR SHOCK ABSORBER
EWA13740
WARNING
This rear shock absorber contains highly
compressed nitrogen gas. Before handling
the rear shock absorber, read and make
sure you understand the following informa-
tion. The manufacturer cannot be held re-
sponsible for property damage or personal
injury that may result from improper han-
dling of the rear shock absorber.
•
Do not tamper or attempt to open the rear
shock absorber.
•
Do not subject the rear shock absorber to
an open flame or any other source of high
heat. High heat can cause an explosion
due to excessive gas pressure.
•
Do not deform or damage the rear shock
absorber in any way. Rear shock absorber
damage will result in poor damping perfor-
mance.
DISPOSING OF A REAR SHOCK
ABSORBER
1. Gas pressure must be released before dis-
Wear eye protection to prevent eye damage
from released gas or metal chips.
REMOVING THE REAR SHOCK
ABSORBER ASSEMBLY
1. Stand the vehicle on a level surface.
Securely support the vehicle so that there is
no danger of it falling over.
Place the vehicle on a suitable stand so that
the rear wheel is elevated.
CHECKING THE REAR SHOCK
ABSORBER ASSEMBLY
INSTALLING THE REAR SHOCK
ABSORBER ASSEMBLY
• Rear shock absorber assembly “1”
Tighten the flange nut until just touching. Do
not fully tighten the nut.
Summary of Contents for MT-03
