19
P-120/P-120S
The Split Mode
To activate the split mode simply press the
[SPLIT]
button so that its indicator
lights. The split mode can be turned off at any time by pressing the
[SPLIT]
but-
ton again so that its indicator goes out.
• The dual and split modes cannot be engaged at the same time.
Selecting the Right and Left Voices
..............................
The voice that was selected before the split mode was engaged becomes
the Right Voice in the split mode. (The Right Voice can also be changed while
in the split mode, by simply pressing the corresponding voice selector.)
To select a Left Voice press the corresponding voice selector while holding
the
[SPLIT]
button (default: [WOOD BASS]). The indicator of the Left
Voice selector will light while the
[SPLIT]
button is pressed, then only the
Right Voice selector and
[SPLIT]
button indicators will remain lit.
To turn the variation on or off for the split voice, hold the
[SPLIT]
button
and press the
[VARIATION]
button or the currently selected voice button.
•
[VARIATION] in the Split Mode
The variation can be individually turned on and off for the split mode voices.
Normally the voice indicator of the Right Voice lights in the split mode. The
[VARIATION] can be used to turn the variation for the Right Voice on or off as
required. While the [SPLIT] button is held, however, the voice indicator of the
Left Voice lights, and in this state the [VARIATION] button can be used to turn
the variation for the Left Voice on or off as required.
•
[EFFECT] in the Split Mode
Depending upon the conditions, one effect type will take priority over the
other. Depth will be decided according to the depth default value of the voice
combination. However, using function F4 (see page 33) you can change the
depth value for each voice as you like.
Effect depth setting via the panel controls (i.e. pressing the [–/NO
▼
] or [+/
YES
▲
] buttons while holding the [EFFECT] button — see page 21) will be
applied to the Right Voice only.
•
[REVERB] in the Split Mode
The reverb type assigned to the Right Voice will take priority over the other. (If
the reverb is set to OFF, the Left Voice’s reverb type will be in affect.)
Reverb depth setting via the panel controls (i.e. pressing the [–/NO
▼
] or [+/
YES
▲
] buttons while holding the [REVERB] button — see page 20) will be
applied to the Right Voice only.
Setting the Split Point
....................................................
The split point is initially set at the F
#
2 key by default. You can change
the split point to any other key by pressing the key while holding the
[SPLIT]
button (the name of the current split-point key appears on the
LED display while the
[SPLIT]
button is held). The split point can also be
set via the Function mode (see below).
Other Split Mode Functions
...........................................
The P-120/P-120S Function mode provides access to a number of other
split-mode functions, listed below. See the corresponding pages for details.
The split mode makes it possible to play two different voices on the keyboard
— one with the left hand and another with the right hand. The Left Voice is played
on all keys to the left of (and including) a specified “split point” key, while the Right
Voice is played on all keys to the right of the split point key.
Example:
• “
b
” is indicated with a lower “
_
”.
• “
#
” is indicated with an upper “
~
”.
A-1
b=1
C 2
F~2
A-1
B
b
-1
C2
F
#
2
NOTE
NOTE
• Split Point .................................... 33
• Split Balance ............................... 33
• Right Voice Octave Shift .............. 34
• Left Voice Octave Shift ................ 34
• Right Voice Effect Depth.............. 34
• Left Voice Effect Depth .................34
• Sustain Pedal Range....................34
• AUX Pedal Range ........................34
• Reset............................................34
17
