Faders
25
ProMix 01 User’s Guide
Faders
ProMix 01 faders are motorized, which means that they can position
themselves automatically. So all faders in a group or stereo pair move
automatically when you move any fader in that group or stereo pair.
Fader positions are stored in mix scenes, so when a mix scene is
recalled the faders move automatically to their new positions. Fader
positions are stored when ProMix 01 is powered OFF. So even if faders
have been moved, they return automatically to their previous posi-
tions when ProMix 01 is powered ON again.
The faders are multifunction controls, which means they are used to
control more than one signal. The signal controlled by a fader at any
given time depends on the selected LCD function. The following table
shows how it works. Essentially, faders work as conventional mixer
faders unless the SEND1, SEND2, SEND3, or SEND4 LCD function
is selected. In this case, they work as channel-to-send level controls.
The current LCD function is shown in the FUNCTION area on the
display. When a SEND LCD function is selected, a flashing fader icon
appears. When there’s no flashing fader icon, you know the faders are
working as channel-to-mix level controls.
ON Buttons
The [ON] buttons are used to turn channels ON and OFF. The input
channel, stereo input channel, and stereo output [ON] buttons turn
their respective channels ON and OFF. The RTN/SEND [ON] button,
on the other hand, is used to turn RTN1, RTN2, SEND3, and SEND4
ON and OFF. Therefore, you must use the RTN/SEND [SEL] button
to select the channel that you want to turn ON and OFF beforehand.
When a channel is turned ON, its [ON] button LED lights up. When
it’s turned off, the LED goes off. Stereo-pair channels are turned ON
and OFF together.
All LCD functions
except—>
SEND1
SEND2
SEND3
SEND4
Channel 1 fader
Channel 1—Fader
Channel 1—SEND1
Channel 1—SEND2
Channel 1—SEND3
Channel 1—SEND4
Channel 16 fader
Channel 16—Fader
Channel 16—SEND1 Channel 16—SEND2 Channel 16—SEND3 Channel 16—SEND4
ST IN fader
ST IN—Fader
ST IN—SEND1
ST IN—SEND2
ST IN—SEND3
ST IN—SEND4
RTN/SEND fader
Selected RTN/SEND
channel
RTN1 (Internal
Effect1 return)
RTN2 (Internal
Effect2 return)
SEND3 (master send
level)
SEND4 (master send
level)
ST OUT fader
Stereo Output (main stereo outputs)
Note:
Fader travel is divided into 128 steps. If a fader is on the border
between steps, it may, in rare circumstances, move one step on its own.
Probably due to a temperature change. In this case, the EDIT indicator
appears and the corresponding Control Change message is output.
6
0
5
10
20
40
60
00
~
~
~
~
~
~
ON
Summary of Contents for Programmable Mixer 01
