PW800W
7
■
DISASSEMBLY PROCEDURE
1.
Top Cover
(Time required : About 1 minute)
Remove the fourteen (14) screws marked [390]. The
top cover can then be removed. (Fig. 1)
2.
Power Supply Unit
(Time required : About 2 minutes)
2-1.
Remove the top cover. (See procedure 1)
2-2.
Remove the six (6) screws marked [240]. The power
supply unit and the window angle can then be removed.
(Fig. 1)
2-3.
Remove the three (3) screws marked [225] and the
screw marked [230A]. The window angle can then be
removed from the power supply unit. (Fig. 1)
2-4.
Remove the four (4) screws marked [230B]. The SW
power angle can then be removed from the power
supply unit. (Fig. 1)
3.
DC Circuit Board
(Time required : About 2 minutes)
3-1.
Remove the top cover. (See procedure 1)
3-2.
Remove the eleven (11) screws marked [310]. The DC
circuit board can then be removed. (Fig. 1)
3-3.
Remove the four (4) screws marked [290] and the
screw marked [300]. The heat sink and holder can then
be removed from the DC circuit board. (Fig. 1)
4.
AC Circuit Board
(Time required : About 1 minute)
4-1.
Remove the top cover. (See procedure 1)
4-2.
Remove the six (6) screws marked [200]. The AC
circuit board can then be removed. (Fig. 1)
5.
LED Circuit Board
(Time required : About 1 minute)
5-1.
Remove the top cover. (See procedure 1)
5-2.
Remove the two (2) screws marked [180]. The LED
circuit board can then be removed. (Fig. 1)
6.
Power Transformer
(Time required : About 1 minute)
6-1.
Remove the top cover. (See procedure 1)
6-2.
Remove the two (2) screws marked [317]. The power
transformer can then be removed. (Fig. 1)
7.
Switch Assembly (Power Switch)
(Time required : About 4 minutes)
7-1.
Remove the top cover. (See procedure 1)
7-2.
Remove the connector pins connected to K6 to K9
terminals of the AC circuit board.
7-3.
Remove the six (6) screws marked [330] and the four
(4) screws marked [355]. The front panel can then be
removed. (Fig. 1)
7-4.
Remove the switch assembly (power switch) by
bending its claw. (Fig. 1)
8.
Front Fan Motor
(Time required : About 3 minutes)
8-1.
Remove the top cover. (See procedure 1)
8-2.
Remove the six (6) screws marked [330] and the four
(4) screws marked [355]. The front panel can then be
removed. (Fig. 1)
8-3.
Remove the power switch. (See procedure 7)
8-4.
Remove the four (4) screws marked [120A]. The fan
motor (front) and the two (2) fan guides can then be
removed. (Fig. 1)
1.
トップカバー
(所要時間:約1分)
[390]のネジ14本を外し、
トップカバーを外します。
(図1)
2.
電源ユニット
(所要時間:約2分)
2-1.
トップカバーを外します。
(1項参照)
2-2.
[240]のネジ6本を外し、
電源ユニットとウインドア
ングルを外します。
(図1)
2-3.
[225]のネジ3本と[230A]のネジ1本を外し、
電源ユ
ニットからウインドアングルを外します。
(図1)
2-4.
[230B]のネジ4本を外し、
電源ユニットからSW電源
取付け金具を外します。
(図1)
3.
DCシート
(所要時間:約2分)
3-1.
トップカバーを外します。
(1項参照)
3-2.
[310]のネジ11本を外し、
DCシートを外します。
(図1)
3-3.
[290]のネジ4本と[300]のネジ1本を外し、
DCシート
からヒートシンクDS/ヒートシンク取付金具を外し
ます。
(図1)
4.
ACシート
(所要時間:約1分)
4-1.
トップカバーを外します。
(1項参照)
4-2.
[200]のネジ6本を外し、
ACシートを外します。
(図1)
5.
LEDシート
(所要時間:約1分)
5-1.
トップカバーを外します。
(1項参照)
5-2.
[180]のネジ2本を外し、
LEDシートを外します。
(図1)
6.
電源トランス
(所要時間:約1分)
6-1.
トップカバーを外します。
(1項参照)
6-2.
[317]のネジ2本を外し、
電源トランスを外します。
(図1)
7.
スイッチAss y
(電源スイッチ)
(所要時間:約4分)
7-1.
トップカバーを外します。
(1項参照)
7-2.
ACシートのK6〜K9端子の圧着端子を外します。
7-3.
[330]のネジ6本と[355]のネジ4本を外し、
フロント
パネルを外します。
(図1)
7-4.
電源スイッチのツメを曲げて、
スイッチAss y
(電源
スイッチ)
を外します。
(図1)
8.
フロントDCファンモーター
(所要時間:約3分)
8-1.
トップカバーを外します。
(1項参照)
8-2.
[330]のネジ6本と[355]のネジ4本を外し、
フロント
パネルを外します。
(図1)
8-3.
電源スイッチを外します。
(7項参照)
8-4.
[120A]のネジ4本を外し、
DCファンモーター
(front)
とファンガイド2個を外します。
(図1)
(分解手順)