CRANKSHAFT
5-66
EAS26040
REMOVING THE CRANKSHAFT JOURNAL
BEARINGS
1. Remove:
• Crankshaft journal lower bearings
(from the lower crankcase)
• Crankshaft journal upper bearings
(from the upper crankcase)
TIP
Identify the position of each crankshaft journal
bearing so that it can be reinstalled in its origi-
nal place.
ET2C01018
CHECKING THE OIL NOZZLES
The following procedure applies to all of the oil
nozzles.
1. Check:
• Oil nozzle
Damage/wear
→
Replace the oil nozzle.
• O-ring
Damage/wear
→
Replace.
• Oil passage
Obstruction
→
Blow out with compressed
air.
EAS26070
CHECKING THE CRANKSHAFT AND CON-
NECTING RODS
1. Measure:
• Crankshaft runout
Out of specification
→
Replace the crank-
shaft.
2. Check:
• Crankshaft journal surfaces
• Crankshaft pin surfaces
• Bearing surfaces
Scratches/wear
→
Replace the crank-
shaft.
3. Measure:
• Crankshaft-journal-to-crankshaft-journal-
bearing clearance
Out of specification
→
Replace the crank-
shaft journal bearings.
ECA13920
Do not interchange the crankshaft journal
bearings. To obtain the correct crankshaft-
journal-to-crankshaft-journal-bearing clear-
ance and prevent engine damage, the
crankshaft journal bearings must be
installed in their original positions.
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Clean the crankshaft journal bearings,
crankshaft journals, and bearing portions of
the crankcase.
b. Place the upper crankcase upside down on
a bench.
c. Install the crankshaft journal upper bear-
ings “1” and the crankshaft into the upper
crankcase.
TIP
Align the projections “a” on the crankshaft jour-
nal upper bearings with the notches “b” in the
upper crankcase.
d. Put a piece of Plastigauge
®
“1” on each
crankshaft journal.
TIP
Do not put the Plastigauge
®
over the oil hole in
the crankshaft journal.
Runout limit C
0.030 mm (0.0012 in)
Journal oil clearance (using
plastigauge
®
)
0.020–0.044 mm (0.0008–
0.0017 in)
Summary of Contents for R6 2009
