background image

Property/Action 

Command Format 

Description 

Response 

logmask 

set logmask <0/1/2/3> 

Configure the debug log level, minimum severity, 

0 - debug,   1 - warning,   2 - error,   3 - off. 

val logmask <0/1/2/3> 

lopassfilter 

set lopassfilter ch <channel 

number>  

<0/12000/8000/4000> 

Configure the low pass filter value for a given 

channel. 

val lopassfilter ch <chanel 

number> 

<0/12000/8000/4000> 

lopassfilter 

get lopassfilter ch <chanel 

number> 

Retrieve the low pass filter value configured for 

given channel. 

val lopassfilter ch <chanel 

number> 

<0/12000/8000/4000> 

macaddr 

get macaddr 

Retrieve system's MAC address. 

val macaddr <mac address> 

mastermutemicgroup 

get mastermutemicgroup  

<group name> 

Retrieve the given group's master mute state,  

0 - unmute,   1 - muted. 

val mastermutemicgroup 

<group name> <0/1> 

mastermutemicgroup 

set mastermutemicgroup 

<group name> <0/1> 

Configure the given group's master mute state, 

0 - unmute,   1 - muted. 

val mastermutemicgroup 

<group name> <0/1> 

rename mutegroup 

rename mutegroup <source 

group> <target group> 

Rename the given source group. 

rename mutegroup <source 

group> <target group> 

micgain 

set micgain ch <channel 

number> <gain value> 

Set gain value in db,  

channel number 1-8 or A. 

val micgain ch <channel 

number> <gain value> 

micgain 

get micgain ch <channel 

number>  

Get gain value in db,  

channel number 1-8 or A. 

val micgain ch <channel 

number> <gain value> 

micgroup 

get micgroup ch <channel 

number> 

Retrieve the group name to which the given mic 

belongs. 

val micgroup ch <channel 

number> <group name> 

micstandbymode 

get micstandbymode ch 

<channel number> 

Retrieve mic standby status,  

channel number 1-8 or A 

val micstandbymode ch 

<channel number> <0/1> 

micstandbymode 

set micstandbymode ch 

<channel number> <0/1/2> 

Set mic into standby mode,  

1 - Enter standby,   0 - leave standby,   2 - toggle. 

val micstandbymode ch 

<channel number> <0/1> 

micstatus 

get micstatus ch <channel 

number> 

Retrieve the given microphone's current status,  

0 - off,    

1 - on,   

2 - standby,   

3 - charging,    4 - out of range,    5 - not paired,   

6 - pairing,      7 - unpairing,  

8 – updating 

val micstatus ch <channel 

number> <status> 

mictype 

get mictype ch <channel 

number> 

Retrieve the given's microphone's type.  

0  - Wearable,    1 - Omni,   

2 - Directional,  

3 - XLR,   

4 - Mini XLR,     5 - Gooseneck,  

10 - Handheld,   11 – unknown  

val mictype ch <channel 

number> <type> 

micversion 

get micversion ch <channel 

number> 

Retrieve mic software version. 

val micversion <channel 

number> <version number> 

mutestatus 

get mutestatus ch <channel 

number> 

Retrieve the mic mute status, value is a comma 

delimited string:  

<mute>,<mute type>,<mute lock> 

val mutestatus ch <channel 

number> 

<mute>,<mute type>,<mute 

lock> 

onlineregstate 

get onlineregstate 

Retrieve online registration state, 

 0 - unregistered,   1 -registered,    

2 - Do not remind me. 

val onlineregstate <state> 

regnotify 

Regnotify 

Register to listen to system notifications. 

regnotify 

outputgain 

get outputgain ch <channel 

number> 

Retrieve the given channel's output gain. 

val outputgain ch <channel 

number> <output gain> 

outputgain 

set outputgain ch <channel 

number> <output gain> 

Configure the given channel's output gain, 

output gain range -20 to 5 db 

val outputgain ch <channel 

number> <output gain> 

outputlevel 

get outputlevel ch <channel 

number> 

Retrieve the channel output level,  

channel number 1/2/../8/A,  

value   0 - mic level,    1 - line level. 

val outputlevel ch <channel 

number> <0/1> 

outputlevel 

set outputlevel ch <channel> 

<value> 

Configure the given channel’s output level, 

channel number 1/2/…/8/A, 

value 0 – mic level, 1 – line level 

val outputlevel ch <channel 

number> <0/1> 

preampgain 

get preampgain ch <channel 

number> 

Retrieve the given channel's preamp gain. 

val preampgain ch <channel 

number> <preamp gain> 

preampgain 

set preampgain ch <channel 

number> <preamp gain> 

Configure the given channel's preamp gain,  

preamp gain range -20 to 0 db. 

val preampgain ch <channel 

number> <preamp gain> 

productname 

get productname 

Retrieve the product name. 

val productname <product 

name> 

Summary of Contents for Revolabs Executive Elite 01-ELITEEXEC8














Reviews: