background image

English

 Owner’s Manual

7

NOTICE

To avoid the possibility of malfunction/ damage to the 
product, damage to data, or damage to other property, 
follow the notices below.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile 

phone, or other electric devices. Otherwise, the device, TV, or radio may 
generate noise.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat 

(such as in direct sunlight, near a heater, or in a car during the day) to prevent 
the possibility of panel disfiguration, damage to the internal components or 
unstable operation.

• Do not place vinyl, plastic or rubber objects on the device, since this might 

discolor the panel or keyboard.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, 

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient 

temperature—when the device is moved from one location to another, or air 
conditioning is turned on or off, for example. Using the device while 
condensation is present can cause damage. If there is reason to believe that 
condensation might have occurred, leave the device for several hours without 
turning on the power until the condensation has completely dried out.

• Always turn the power off when the device is not in use.

• XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, 

pin 2: hot (+), and pin 3: cold (-).

Information

About copyrights

 * Copying of the commercially available musical data including but not limited to 

MIDI data and/or audio data is strictly prohibited except for your personal use.

About this manual

 * The illustrations and LCD screens as shown in this manual are for instructional 

purposes only, and may appear somewhat different from those on your device.

 * The company names and product names in this manual are the trademarks or 

registered trademarks of their respective companies.

 * Specifications and exterior appearance may be subject to change without prior 

notice as a result of improvements.

(weee_eu)

Yamaha cannot be held responsible for damage caused by improper use or 
modifications to the device, or data that is lost or destroyed.

European Models
Inrush Current based on EN 55103-1:2009
2A (on initial switch-on)
2A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4

Handling and Maintenance

Connectors

Information for Users on Collection and Disposal of Old 
Equipment

This symbol on the products, packaging, and/or 
accompanying documents means that used electrical 
and electronic products should not be mixed with 
general household waste.

For proper treatment, recovery and recycling of old 
products, please take them to applicable collection 
points, in accordance with your national legislation and 
the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable 
resources and prevent any potential negative effects on human health and the 
environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please 
contact your local municipality, your waste disposal service or the point of sale 
where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your 
dealer or supplier for further information.

[Information on Disposal in other Countries outside the European 
Union]

This symbol is only valid in the European Union. If you wish to discard these 
items, please contact your local authorities or dealer and ask for the correct 
method of disposal.

PA_en_1

  2/2

Summary of Contents for Ro8-D

























Reviews: