Pin No.
Function Name
I/O
TFT Mode
LCD STN monochr.
LCD STN monochr.
(double)
LCD STN color
LCD STN color
(bias)
V3
LCDD[17]
O
RED5
U4
LCDD[16]
O
RED4
V4
LCDD[15]
O
RED3
T5
LCDD[14]
O
RED2
U5
LCDD[13]
O
RED1
V5
LCDD[12]
O
(RED0)
R6
LCDD[11]
O
GREEN5
T6
LCDD[10]
O
GREEN4
U6
LCDD[9]
O
GREEN3
V6
LCDD[8]
O
GREEN2
R7
LCDD[7]
O
GREEN1
DATAHIGH3
DATA7
DATA7
T7
LCDD[6]
O
GREEN0
DATAHIGH2
DATA6
DATA6
U7
LCDD[5]
O
BLUE5
DATAHIGH1
DATA5
DATA5
V7
LCDD[4]
O
BLUE4
DATAHIGH0
DATA4
DATA4
R8
LCDD[3]
O
BLUE3
DATA3
DATALOW3
DATA3
DATA3
T8
LCDD[2]
O
BLUE2
DATA2
DATALOW2
DATA2
DATA2
U8
LCDD[1]
O
BLUE1
DATA1
DATALOW1
DATA1
DATA1
V8
LCDD[0]
O
(BLUE0)
DATA0
DATALOW0
DATA0
DATA0
T10
LCDCLK
O
Byte clock
CL2
CL2
CL2
CL2
V9
LCDCTRL[3]
O
Display off
Display off
Display off
Display off
Display off
U9
LCDCTRL[2]
O
Vsync
FLM
FLM
FLM
FLM
T9
LCDCTRL[1]
O
HSync
CL1
CL1
CL1
CL1
R9
LCDCTRL[0]
O
DVALID
M/Bias
Pin No.
Function Name
I/O
Detail of Function
F2
RTCXIN
I
No connection. Leave this pin open circuit.
G2
RTCXOUT
O
No connection. Leave this pin open circuit.
F1
VDD33RTC
Power
No connection. Leave this pin open circuit.
E1
VSS33RTC
Power
Ground (0 V) for RTC
Pin No.
Function Name
I/O
Detail of Function
D6
NRES12REF
I
Voltage reference input. NRES12OUT is release when this input voltage exceeds VTH12.
C5
NRES12OUT
O
Open-drain reset (active low) for 1.2V core power supply.
D5
NRES33REF
I
Voltage reference input. NRES33OUT is release when this input voltage exceeds VTH33.
D4
NRES33OUT
O
Open-drain reset (active low) for 3.3V core power supply
Pin No.
Function Name
I/O
Detail of Function
B1
USBD+
I/O
Positive data line that is connected to the serial USB cable.
A1
USBD–
I/O
Negative data line that is connected to the serial USB cable.
E2
USBID
I
USB ID pin of mini-AB receptacle.
C2
USBREXT
I
External bias resistor (2K7, 1%); connect resistor to VSSUSB.
D2
USBVBUS
I
VBUS voltage sense.
E3
USBVBUSDRV
O
Control signal to control VBUS 5V voltage source.
C4
USBXTALI
I
Oscillator circuit input for a 24.000 MHz crystal (optional).
Without external crystal, pull this pin to GND.
C3
USBXTALO
O
Oscillator circuit output for a 24.000 MHz crystal (optional).
Without external crystal, leave this pin open.
D3
USBATST
–
Do not connect.
USB 2.0 OTG
Power-on Reset Pins
Real-Time Clock (RTC) Pins (RTC is Not Supported)
LCD Interface
76
RX-V475/HTR-4066/RX-V500D
RX-V475/HTR-4066/
RX-V50
0D
Summary of Contents for RX-V500D
