24
2.2.2.4 Normal Voice bulk dump
This message sets the NORMAL VOICE block (refer to tables <2-1>, <2-2>, <2-9>,
<2-10>).
To receive this message, the Bulk Header and Bulk Footer of Bulk Control must be
received before and after reception, respectively.
The Bulk Header determines the Memory Bank/Voice number to which the data is stored.
2.2.2.5 Drum Voice bulk dump
This message sets the NORMAL VOICE block (refer to tables <2-1>, <2-2>, <2-11>,
<2-12>).
To receive this message, the Bulk Header and Bulk Footer of Bulk Control must be
received before and after reception, respectively.
The Bulk Header determines the Memory Bank/Voice number to which the data is stored.
2.3
Parameter request
This message requests transmission of a parameter value.
The output is transmitted in the Parameter Change message format (refer to 2.1.x).
2.3.1 XG parameter request
This message requests transmission of XG parameter settings.
Settings are transmitted in the format of an XG parameter change (refer to 2.1.3).
11110000
F0H
Exclusive status
01000011
43H
YAMAHA ID
0001nnnn
3NH
N:Device Number
01001100
4CH
Model ID
0ggggggg
GGH
Address High
0mmmmmmm
MMH
Address Mid
0lllllll
LLH
Address Low
11110111
F7H
End of Exclusive
2.3.2 S08 native parameter request
This message requests transmission of a parameter value unique to the S08.
The output is transmitted in the format of a S08 native parameter change (refer to 2.1.4).
11110000
F0H
Exclusive status
01000011
43H
YAMAHA ID
0001nnnn
3NH
N:Device Number
01101100
6CH
Model ID
0ggggggg
GGH
Address High
0mmmmmmm
MMH
Address Mid
0lllllll
LLH
Address Low
11110111
F7H
End of Exclusive
2.4
Dump request
This message requests transmission of a specific block of parameter values.
The output is the same as the bulk dump format.
2.4.1 XG dump request
This message requests transmission of all parameters of the specified block of XG
parameters.
The output is the same as the format of XG bulk dump (refer to 2.2.1).
11110000
F0H
Exclusive status
01000011
43H
YAMAHA ID
0001nnnn
2NH
N:Device Number
01001100
4CH
Model ID
0ggggggg
GGH
Address High
0mmmmmmm
MMH
Address Mid
0lllllll
LLH
Address Low
11110111
F7H
End of Exclusive
Address is valid only when the beginning of the block has been specified.
2.4.2 S08 native dump request
This message requests transmission of all parameters of the specified block of S08 native
parameters.
The output is in the same format as an S08 native bulk dump (refer to 2.2.2).
11110000
F0H
Exclusive status
01000011
43H
YAMAHA ID
0001nnnn
2NH
N:Device Number
01101100
6CH
Model ID
0ggggggg
GGH
Address High
0mmmmmmm
MMH
Address Mid
0lllllll
LLH
Address Low
11110111
F7H
End of Exclusive
Address is valid only when the beginning of the block has been specified.
No System Exclusive Message is received when the Compare function is active.
3.
Realtime messages
3.1
Active sensing
a) Transmission
Transmitted at every 270 msec.
b) Receive
Once FE has been received, failure to receive any MIDI message for an interval longer
than approximately 300 msec will cause processing to be performed as if ALL SOUND
OFF, ALL NOTE OFF, and RESET ALL CONTROLLERS messages were received, and
the unit will reset to a condition in which FE was never received.
3.2
Timing Clock
Status: F8H
3.3
Start
Status: FAH
3.4
Continue
Status: FBH
3.5
Stop
Status: FCH
