Yamaha S112 Owner'S Manual Download

Page: 10 / 84

Recall and Store

DG100-

212A

/DG80-

210A

/DG80-

112A

/DG130H

A MIDI foot controller or other external MIDI device can
be used to select and recall memory. Refer to the follow-
ing page to page 13 for details.

The memory number to be recalled, shown on
the display, goes from flashing to lit.

Execute Recall

Select the memory number to be recalled.

Initialize the memory

While holding both the

button and

button,

turn the Power Switch ON, the initialize to factory preset opera-
tion will be carried out and the entire memory will be returned to
its factory preset condition.

When the initialize operation is carried out, data in memory num-
bers 1-80 will be re-written with data in the Patch List and the
data in memory numbers 81 – 128 will also be reset to their fac-
tory preset condition. Any data you have saved to memory will be
erased, so we strongly recommend that you save any important
data to an external MIDI device or document the settings before
carrying out the operation.

■

Recall Memory (Recall)

Sound settings stored in memory can easily be recalled by selecting a

memory number.

When a memory is recalled, the current settings will be
changed. If you want to keep the settings, use the Store op-
eration, described on the right side of this page, to store set-
tings to memory.

Press the

button, the AMP or EFFECT mode display

will light.

Use the

buttons to select the memory number you

want to recall. The memory number will appear on the display

(flashing).

Press the

button. The flashing memory number will

light. Each of the knobs, and the Amp Select Display will change

according to the data recalled from memory.

* Settings will not change until the

button is pushed.

* TRIM and OUTPUT knob settings will not change with the Recall op-

eration.

* It takes anywhere from 1 – 10 seconds for the knobs to change to their

set positions however, internal settings (sound) will change instantly.

* “

” will appear on the display if the volume knob does not go to its

assigned position, or the device does not recognize the recall command
after 20 seconds has elapsed from the start of the recall operation. Con-
tinued use of the device in this condition may result in fire or electrical
shock. Take the unit to the music dealer where you purchased it, or to the
nearest Yamaha Service Center for repair.

Lights

HINT

Some hints on storing memory numbers

When storing data to memory numbers, divide the memory num-

bers 1 – 128 into several groups.

Recalling memory numbers from these groups is much more con-

venient. For example:

• Create groups according to the amp type used (LEAD1, DRIVE 1, etc.).

• Create groups based on sound types (Distortion, Clean, etc.)

• Create groups based on live performance song lists.

• Create groups based on the type of guitar used (humbucker, etc.).

It is also a good idea to keep a chart handy listing the types of

sounds are stored in memory numbers.

The memory number to be stored.
Flashing

→

8.8.

→

Lights

Execute Store

Select the memory number.

Data stored in memory (1 – 128) can be saved to an exter-
nal MIDI storage device. Refer to page 12 for details.

■

Store Settings

Use the procedure on page 9 and create a sound using the

eight preset amp types and control knobs on the front panel.

* Each of the Utility Mode’s settings cannot be stored in individual memory.

When the power is switched OFF, each memory’s settings are stored in
memory as common settings. When the power is turned ON, those set-
tings are recalled.

Press the

button, the AMP or EFFECT mode display

lamp will light.

Using the

buttons, select a memory number to which

the settings will be saved. The memory number will flash in the

display.

* Press and hold either of the

buttons makes memory numbers

cycle rapidly.

* The third digit of the memory number (100 – 128) is represented by a dot

between the two digits.