background image

SWP1 Owner’s Manual

7

SOFTWARE LICENCE 

AGREEMENT

This agreement is an agreement between you, the customer, 
and Yamaha Corporation (hereafter referred to as “Yamaha”) 
defining the conditions under which Yamaha provides firmware 
for this Yamaha network product (hereafter referred to as the 
Product) and related programs, printed material, and electronic 
files (hereafter referred to as the Software).

The Software may be used only for the purpose of operating it on 
the Product or on a personal computer or similar device. This 
agreement applies to the Software provided by Yamaha to the 
customer and to copies of the Software created by the customer 
in compliance with section 1 subsection (1) of this agreement.

1. Permission to use

(1) The customer may install and use the Software on a Product 

or a personal computer or similar device owned by the 
customer.

(2) With the exceptions that are explicitly defined by this 

agreement, the customer shall not permit the reuse of, sell, 
distribute, rent, lease, lend, or transfer the Software, nor 
upload it to any website or server where it could be 
accessed by specified or unspecified numbers of people, 
nor duplicate, translate, adapt it, or rewrite it into any other 
program language. The customer shall not correct, revise, 
reverse-assemble, reverse-compile, or perform any reverse 
engineering of the Software, and may not cause any third 
party to perform such actions.

(3) The customer shall not modify, erase, or delete the Yamaha 

copyright indications that are included in the Software.

(4) With the exceptions that are explicitly defined by this 

agreement, Yamaha does not grant or permit the customer 
any of Yamaha's intellectual property rights.

2. Property rights

The Software is protected by copyright law and by other laws, 
and is the property of Yamaha. The customer hereby agrees that 
no property rights or intellectual property rights related to the 
Software are granted by Yamaha to the customer by this 
agreement nor any other means.

3. Export restrictions

The customer shall abide by all applicable export regulations 
and rules of the relevant countries, and shall not export or re-
export the Software, neither in part nor in whole, in violation of 
any applicable rules and regulations.

4. Support and updates

Yamaha, its subsidiaries, their sales representatives and 
dealers, and any other party handling or distributing the 
Software do not accept any responsibility for maintaining the 
Software nor for supporting the customer's use of the Software. 
Nor do the aforementioned parties have any responsibility to 
update the Software, to fix bugs, or to provide support.

5. Limitation of responsibility

(1) The software is licensed for use “in its current state (as-is).” 

Yamaha, its subsidiaries, their sales representatives and 
dealers, and any other party handling or distributing the 
Software make no warranty, neither explicit nor implicit, 
regarding the merchantability or suitability of the Software for 
any particular purpose.

(2) Yamaha, its subsidiaries, their sales representatives and 

dealers, and any other party handling or distributing the 

Software shall bear no responsibility for any damages 
(including but not limited to lost profit and any other 
consequential or incidental damages) that may arise from 
the use of or inability to use the Software. This shall be the 
case even if Yamaha, its subsidiaries, their sales 
representatives and dealers, or any other party handling or 
distributing the Software had been informed of the possibility 
of such damages.

(3) Yamaha, its subsidiaries, their sales representatives and 

dealers, and any other party handling or distributing the 
Software shall bear no responsibility for any dispute between 
the customer and a third party that may arise from or related 
to the use of the Software.

6. Term of validity

(1) This agreement shall continue in force until it is terminated 

by the following sub-sections (2) or (3).

(2) The customer may terminate this agreement by deleting all 

instances of the Software that are installed on the Product or 
on a personal computer or similar device.

(3) This agreement shall immediately terminate if the customer 

violates any of the terms of this agreement.

(4) Upon the termination of this agreement due to sub-section 

(3) above, the customer shall immediately delete all 
instances of the Software that are installed on the Product or 
on a personal computer or similar device.

(5) Regardless of any clauses of this agreement, the provisions 

of sections 2 through 6 of this agreement shall continue in 
force even after the termination of this agreement.

7. Separability

Even if any clause of this agreement should become invalid, the 
remainder of the agreement shall remain in force.

8

. U.S. GOVERNMENT RESTRICTED RIGHTS 

NOTICE:

The Software is a “commercial item,” as that term is defined at 
48 C.F.R. 2.101 (Oct 1995), consisting of “commercial computer 
software” and “commercial computer software documentation,” 
as such terms are used in 48 C.F.R. 12.212 (Sept 1995). 
Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 
through 227.72024 (June 1995), all U.S. Government End Users 
shall acquire the Software with only those rights set forth herein.

9. General articles

The customer agrees that this agreement is the complete and 
only declaration of agreement between the customer and 
Yamaha regarding all matters prescribed by this agreement, and 
that it takes precedence over all proposals, prior agreements, or 
any other communication between the customer and Yamaha, 
whether oral or written. No change to this agreement shall have 
any force unless it is signed by a representative who is duly 
authorized by Yamaha.

10. Jurisdiction

This agreement shall be under the jurisdiction of the laws of 
Japan, and shall be interpreted according to those laws.

Summary of Contents for SWP1-16MMF




















Reviews: