background image

2

Precautions

Always use the timpani in a safe manner.

In order to prevent damage or injury, we urge you to carefully read and follow the instructions

listed below.

In the case of use by young children, we recommend proper guidance be given by a knowledge-

able adult.

Disregarding these warnings or misuse may result in death or personal injury.

Warnings

• Never place the timpani on unstable surfaces such

as an unstable riser or sloped surface. The timpani

may tip over or fall resulting in damage or injury.

• Never lean on or climb on the instrument. It may over-

turn resulting in damage or injury.

• Be careful around the instrument. Bumping into it may

result in injury or cause it to overturn. Keep small

children away from the instrument.

• Never place your fingers or foot into the moving parts

or the space under the pedal or base. Serious injury

can result if fingers or feet become pinched.

• When rolling the timpani on its casters, grip it by its

frame and move it only on smooth, flat surfaces.

1. Do not move on sloping, rough, or gravel surfaces.

2. Do not run with the timpani. It may be difficult to stop

the instrument which can cause injury or damage.

• If the timpani must be carried, do so with two or more

persons, make sure to grip the timpani by its lugs.

Caution

• Replace torn heads as soon as possible. The torn

edge of the head is sharp and can cut hands or fin-

gers.

• When operating the pedal, do not touch the hoop,

head, or tuning indicator. Fingers may become caught

or pinched resulting in injury.

• Do not put your hands inside any of the parts of the

timpani (inside the tuning indicator, base, lugs, etc.)

• Do not use the mallet for anything besides playing

the instrument.

Do not allow children strike others with the mallet as

it can cause injury or become damaged.

Tuning Indicator

Tuning bolt

Head

Hoop

tp3100ea_en_om.6pm

08.2.5, 9:28 AM

2

Summary of Contents for TP-3123












Reviews: