Yamaha TP-3123 Owner'S Manual Download

Page: 3 / 11

Nomenclature & Lubrication

Supplied Accessories

• Tuning Key ......................................... 1

• Mallets ......................................... 1 set

• Hex Wrench ....................................... 1

• Spring Adjustment Wrench ................ 1

Tuning Bolt

■

Lubrication

Apply a high quality grease or lubricant to the moving

parts indicated by the arrows in the diagram on the right.

This should be done at least once a year, or as needed.

* A spray type lubricant is recommended.

* Do not touch the lubricated parts.

Head Protector

Pointer Lock Nut

Hoop (Counter Hoop)

Head

Kettle Edge

Caster

Base

Pointer Adjustment Knob

Tuning Indicator

Kettle

Pedal

Pedal Leg

Sliding Leg

■

Nomenclature

Caution

Never place your fingers or foot into the moving parts or the
space under the pedal or base.
Serious injury can result if fingers or feet become pinched.

Leg Lock
Bolt Handle

Spring Tension
Adjustment Bolt

Lug

tp3100ea_en_om.6pm

08.2.5, 9:28 AM

Summary of Contents for TP-3123












Search results

Summary of Contents for TP-3123

Reviews:

Related manuals for TP-3123

Brands by name

Popular brands

Yamaha TP-3123, Owner'S Manual

Search results

Summary of Contents for TP-3123

Reviews:

Related manuals for TP-3123

Brands by name

Popular brands