Yamaha XP500 Service Manual Download

Page: 80 / 559

2 - 40

SPEC

CABLE ROUTING

Rear brake lock lever cable

Negative battery lead

Seat lock cable (left)

Frame

Wire harness

Storage box

V-belt replacement indicator reset coupler lead

sensor lead

Fuel hose

After adjusting the adjustment nut, attach the
front and rear parts of the boot tightly.

Pass the seat lock cable between wire harness
and frame.

Use the plastic holder on the back of the frame
to hold the radiator fan motor lead.

Connect the wire harness (wire taped area) to
the T stud of frame.

Pass the main switch lead between stay 1 and
seat lock cable.

É Ê

S N

Summary of Contents for XP500
















































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XP500

Reviews:

Related manuals for XP500

Brands by name

Popular brands

Yamaha XP500, Service Manual

Search results

Summary of Contents for XP500

Reviews:

Related manuals for XP500

Brands by name

Popular brands