Check the following points.
・
Is the optimizer microphone firmly connected to this unit?
・
Is the optimizer microphone placed in a proper loacation?
・
Are there any large obstacles in between the optimizer microphone and the
walls in your listening room?
・
The AUTO SETUP procedure starts in 10 seconds after pressing ENTER
on step 7. To achieve the best results possible, evacuate yourself for your
listening room until the AUTO SETUP procedure is completed.
・
To cancel the AUTO SETUP procedure after it is started, press RETURN.
・
The AUTO SETUP procedure takes about 3 minutes.
Press ENTER to start the AUTO SETUP procedure.
The following screen appears on the TV and the AUTO SETUP procedure
starts in 10 seconds.
The setup screen automatically changes during the AUTO SETUP
procedure.
If any error occurs, the corresponding error message appears on the screen.
In this case, see “Error messages for AUTO SETUP” on page 35 in the
Owner’s Manual and then follow the instructions. To start the AUTO SETUP
procedure once again, press RETURN and then carry out the procedure from
step 5.
When the AUTO SETUP procedure is complete, the following screen
appears on the TV.
*
This is an example of the result screen.
The result may differ depending on the
environment.
Press ENTER.
The result is confirmed and the following screen appears on the TV for 2
seconds and then the menu screen disappears from the TV.
The new settings are automatically saved in the system memory.
Disconnect the optimizer microphone and keep it in a safe place.
Enjoy TV or DVD audio in surround sound.
For instructions on your TV or DVD player, refer to the owner’s manual supplied with each component.
Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in
step 4.
Enjoying surround sound
Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that
best match your listening environment.
This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments
that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are
no children around in the listening room while the AUTO SETUP procedure is in progress.
Press STANDBY/ON on
the remote control.
The power of this unit turns on.
If a subwoofer with adjustable volume and
crossover/high cut frequency controls is
connected to this unit, set the volume
between 11 and 1 o’clock as viewed on a
conventional clockface and set the
crossover/high cut frequency to the
maximum.
Turn on the power of your TV.
Select the appropriate video input
on your TV.
Set the operation mode selector to YSP.
Press and hold AUTO SETUP for more than 2
seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the video pin cable (connection
5
in the diagram on the front page) is connected properly and then press
YSP followed by MENU.
If you hear sound output from your TV speakers, turn down the volume level
until you cannot hear any sound.
Use the remote control supplied with your TV.
Press /– on the remote control to adjust
the volume level of this unit.
Press one of the beam mode buttons on the
remote control to select the desired beam mode.
Select one of the three beam modes that best matches the current input source of
this unit.
For further information on the beam modes, see page 42 in the Owner’s Manual.
To fine-tune the listening environment parameters manually or make advanced settings for
speaker positions, sound beams, etc., see “MANUAL SETUP” on page 60 in the Owner’s Manual.
TV VOL
VOLUME
MUTE
TV INPUT
TV MUTE
CH
STEREO
MY BEAM SURROUND
SPORTS
5BEAM
ST+3BEAM
3BEAM
MUSIC
MOVIE
2
1
3
4
5
6
7
8
9
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
AUTO SETUP
INPUT2
TV
2
1
3
SLEEP
5BEAM
ST+3BEAM
3BEAM
VOL MODE
AUTO
SETUP INPUTMODE
MACRO
INPUT1
AUX
TV
STB
VCR
DVD
CH LEVEL
MENU
RETURN
TEST
ENTER
YSP
TV/AV
Will begin in 10sec
Please leave the room
**--------
[RETURN]:Cancel
AUTO SETUP START
AUTO SETUP COMPLETE
Please remove the MIC from
the YSP and the listening
position.
POWER
POWER
STANDBY/ON
TV
TV
AV
AUX
STB
VCR
DVD
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER:NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
SHOW RESULT
3
4
8
7
4
5
6
2
Select the TV channel using
the remote control supplied
with your TV.
INPUT2
TV
SLEEP
VOL MODE
AUTO
SETUP INPUTMODE
MACRO
INPUT1
TV
INPUT2
TV
SLEEP
VOL MODE
AUTO
SETUP INPUTMODE
MACRO
INPUT1
AUX
TV
STB
VCR
DVD
Select the DVD video input on your
TV.
Enjoying TV in surround sound
3
1
3
1
Enjoying DVDs in surround sound
1
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
MAX
Subwoofer
CH LEVEL
MENU
RETURN
TEST
ENTER
YSP
TV/AV
Continued
from the front
5
2
CH LEVEL
MENU
RETURN
TEST
ENTER
YSP
TV/AV
Set the operation mode selector to YSP .
Press TV on the remote
control of this unit.
This unit switches to the TV playback mode.
Press DVD on the remote control of this unit,
and then start playback on the DVD player.
This unit switches to the DVD playback mode.
CH LEVEL
MENU
RETURN
TEST
ENTER
YSP
TV/AV
6
