background image

SYMPTOM

Power is not supplied even though the
POWER switch is ON.

No sound .

Sound level is too low.

CAUSE

The power plug is not securely connected.

The VOLUME control is set to 0.

Speaker cables are not connected securely.

Speaker cables are connected incorrectly.

Setting of the PHASE switch is not proper.

A source sound with few bass frequencies is
played.

It is influenced by standing waves.

REMEDY

Connect it securely.

Turn the VOLUME control to right.

Connect them securely.

Connect them correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”.

Set the switch to the other position.

Play a source sound with bass frequencies.
Set the HIGH CUT control to a higher
position. (Turn the knob to right.)

Re-position the subwoofer or break up the
parallel surface by placing bookshelves etc.
along the walls.

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested.  If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.

TROUBLESHOOTING

SPECIFICATIONS

Type .....................Active Servo Processing Subwoofer System
Speaker Unit .................18 cm (7-1/16”) cone woofer (JA1821)

magnetic-shield type x 2

Amplifier Output ..................70W/5 ohms (THD 0.1%, 100 Hz)
High-Cut Filter...............................40 Hz–140 Hz (–24 dB/oct.)
Frequency Response ..........................21 Hz–160 Hz (–10 dB)
Power Supply

U.S.A. and Canada models........................AC 120V, 60 Hz
Australia and U.K. models.........................AC 240V, 50 Hz
Europe model .............................................AC 230V, 50 Hz
General model ..................AC 110/120/220/240V, 50/60 Hz

Power Consumption........................................................100W
Dimensions (W x H x D) .............215 mm x 590 mm x 412 mm

(8-7/16” x 23-1/4” x 16-1/4”)

Weight .....................................................15.5 kg (34 lbs. 2 oz.)

* Please note that all specifications are subject to change

without notice.

YST-SW120

Type .....................Active Servo Processing Subwoofer System
Speaker Unit .................18 cm (7-1/16”) cone woofer (JA1822)

magnetic-shield type

Amplifier Output ..................50W/6 ohms (THD 0.1%, 100 Hz)
High-Cut Filter...............................50 Hz–200 Hz (–24 dB/oct.)
Frequency Response ..........................25 Hz–250 Hz (–10 dB)
Power Supply

U.S.A. and Canada models........................AC 120V, 60 Hz
Australia and U.K. models.........................AC 240V, 50 Hz
Europe model .............................................AC 230V, 50 Hz
General model ..................AC 110/120/220/240V, 50/60 Hz

Power Consumption..........................................................70W
Dimensions (W x H x D) .............210 mm x 475 mm x 360 mm

(8-1/4” x 18-11/16” x 14-3/16”)

Weight ........................................................10 kg (22 lbs. 0 oz.)

* Please note that all specifications are subject to change

without notice.

YST-SW60

YAMAHA  ELECTRONICS  CORPORATION,  USA 6660  ORANGETHORPE  AVE.,  BUENA  PARK,  CALIF.  90620,  U.S.A.
YAMAHA  CANADA  MUSIC  LTD. 135  MILNER  AVE.,  SCARBOROUGH,  ONTARIO  M1S  3R1,  CANADA
YAMAHA  ELECTRONIK  EUROPA  G.m.b.H. SIEMENSSTR.  22-34,  D-2084  RELLINGEN  BEI  HAMBURG,  F.R.  OF  GERMANY
YAMAHA  ELECTRONIQUE FRANCE  S.A. 17  RUE  DES  CAMPANULES,  LOGNES  77321  MARNE  LA  VALLEE  CEDEX  2,  FRANCE
YAMAHA  ELECTRONICS  (UK)  LTD. YAMAHA  HOUSE,  200  RICKMANSWORTH  ROAD  WATFORD,  HERTS  WD1  7JS,  ENGLAND
YAMAHA  SCANDINAVIA  A.B. J  A  WETTERGRENS  GATA  1,  BOX  30053,  400  43  VÄSTRA  FRÖLUNDA,  SWEDEN
YAMAHA  MUSIC  AUSTRALIA  PTY,  LTD. 17-33  MARKET  ST.,  SOUTH  MELBOURNE,  3205  VIC.,  AUSTRALIA

VR43210-0  BWWO,BR            Printed in Japan

Summary of Contents for YST-SW120













Reviews: