Yamaha YZF-R1 2007 Service Manual Download | Manualshive

Page: 19 / 442

background image

FEATURES

1-10

Air intake temperature display

The air intake temperature display indicates
the temperature of the air drawn into the air fil-
ter case. Push the “RESET” button to switch
the coolant temperature display to the air
intake temperature display.

NOTE:

• Even if the air intake temperature is set to be

displayed, the coolant temperature warning
light comes on when the engine overheats.

• When the key is turned to “ON”, the coolant

temperature is automatically displayed, even
if the air intake temperature was displayed
prior to turning the key to “OFF”.

• When the air intake temperature display is

selected, “A” is displayed before the temper-
ature.

Self-diagnosis device

This model is equipped with a self-diagnosis
device for various electrical circuits.
If any of those circuits are defective, the engine
trouble warning light will come on, and then the
display will indicate a two-digit error code.
This model is also equipped with a self-diagno-
sis device for the immobilizer system.
If any of the immobilizer system circuits are
defective, the immobilizer system indicator

light will flash, and then the display will indicate
a two-digit error code.

NOTE:

If the display indicates error code 52, this could
be caused by transponder interference. If this
error code appears, try the following.

1. Use the code re-registering key to start the

engine.

NOTE:

Make sure there are no other immobilizer keys
close to the main switch, and do not keep more
than one immobilizer key on the same key ring!
Immobilizer system keys may cause signal
interference, which may prevent the engine
from starting

2. If the engine starts, turn it off and try start-

ing the engine with the standard keys.

3. If one or both of the standard keys do not

start the engine, take the vehicle, the code
re-registering key and both standard keys
to a Yamaha dealer and have the standard
keys re-registered.

If the display indicates any error codes, note
the code number, and then have a Yamaha
dealer check the vehicle.

CAUTION:

ECA4C81019

If the display indicates an error code, the
vehicle should be checked as soon as pos-
sible in order to avoid engine damage.

Display brightness and shift timing indica-
tor light control mode

1. Air intake temperature display

1. Error code display

1. Display brightness
2. Shift timing indicator light activation/deacti-

vation

3. Shift timing indicator light
4. Brightness level

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys

email: info@motomatrix.co.uk

«
...
17
18
19
20
21
...
»

Summary of Contents for YZF-R1 2007



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for YZF-R1 2007

Brand: R&G Pages: 4

Brand: Honda Pages: 100

Brand: R&G Pages: 24

Brand: hepco & becker Pages: 5

Brand: Honda Pages: 91

Brand: MV Agusta Pages: 36

Brand: Takegawa Pages: 2

Krauser 630.2516

Brand: hepco & becker Pages: 6

Intruder VS1400

Brand: Suzuki Pages: 291

Brand: GÜDE Pages: 80

Brand: GÜDE Pages: 88

HelmetTalk HTCS-3O

Brand: Nady Systems Pages: 2

Brand: Legend Pages: 2

Brand: Yamaha Pages: 27

Brand: Yamaha Pages: 71

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands