Yamaha YZFR1W 2007 Service Manual Download

Page: 395 / 429

IMMOBILIZER SYSTEM

8-76

Immobilizer system indicator light fault code indication

Digit of 10 : Cycles of 1 sec. ON and 1.5 sec. OFF.
Digit of 1 : Cycles of 0.5 sec. ON and 0.5 sec. OFF.
Example: fault code 52

IMMOBILIZER
UNIT

Codes transmitted
between the ECU
and the immobilizer
unit do not match.

Noise interference or dis-
connected lead/cable.
1 Interference due to

radio wave noise.

2 Disconnected commu-

nication harness.

3 Immobilizer unit mal-

function.

4 ECU failure.

(The ECU or immobi-
lizer unit was replaced
with a used unit from
another vehicle.)

1 Register the code

re-registering key.

2 Check the wire

harness and con-
nector.

3 Replace the main

switch/immobi-
lizer unit.

4 Replace the ECU.

IMMOBILIZER
UNIT

Key code registra-
tion malfunction.

Same standard key was
attempted to be regis-
tered two consecutive
times.

ECU

Undefinition code is
received.

Noise interference or dis-
connected lead/cable.

1 Check the wire

harness and con-
nector.

2 Replace the main

switch/immobi-
lizer unit.

3 Replace the ECU.

Fault
code

Part

Symptom

Cause

Action

a. Light on
b. Light off

Summary of Contents for YZFR1W 2007














































































































































































































































































































































































































































Search results

Summary of Contents for YZFR1W 2007

Reviews:

Related manuals for YZFR1W 2007

Brands by name

Popular brands

Yamaha YZFR1W 2007, Service Manual

Search results

Summary of Contents for YZFR1W 2007

Reviews:

Related manuals for YZFR1W 2007

Brands by name

Popular brands