background image

 

 

 

Cautions in Using with Safety 

Fundamental Matters of 

“WARNING!” and “CAUTION!” 

 

WARNING! 

 

 

Do not use this unit in an area where there is flammable or explosive gas 

Never use this unit in an area where there is flammable or explosive gas. 
This unit is not explosion-proof.    An arc may be generated when the power switch is turned on or off, 
and fire/explosion may result. (Refer to page12 

“List of Dangerous Substances”.) 

 

 

Always ground this unit

 

Always ground this unit on the power equipment side in order to avoid electrical shock due to a power 
surge. 

 

 

If a problem occurs

 

If  smoke  or  strange  odor  should  come  out  of  this  unit  for  some  reason,  turn  off  the  power  key  right 
away,  and  then  turn  off  the  circuit  breaker  and  the  main  power.    Immediately  contact  a  service 
technician  for  inspection.  If  this  procedure  is  not  followed,  fire  or  electrical  shock  may  result.  Never 
perform repair work yourself, since it is dangerous and not recommended. 

 

 

Do not use the power cord if it is bundled or tangled

 

Do not use the power cord if it is bundled or tangled.    If it is used in this manner, it can overheat and 
fire may be caused. 

 

 

Do not process, bend, wring, or stretch the power cord forcibly

 

Do not process, bend, wring, or stretch the power cord forcibly.    Fire or electrical shock may result. 

 

 

Substances that can not be used

 

Never  use  explosive  substances,  flammable  substances  and  substances  that  include  explosive  or 
flammable ingredients in this unit. Explosion or fire may occur. 

 

 

Do not disassemble or modify this unit

 

Do not disassemble or modify this unit.    Fire or electrical shock or failure may be caused. 

 

CAUTION! 

 

 

During a thunder storm

 

During a thunderstorm, turn off

 

the power key immediately, then turn off the circuit breaker and the main 

power.    If this procedure is not followed, fire or electrical shock may be caused. 

Summary of Contents for SA400


























Reviews: