background image

2

Distinguished Users:

We are very glad that you choose our company's products and feel sure that you will find the

convenience that our products bring to you and the joy of promoting the policy of “low carbon and

environmental protection”.

Please do not forget to read the “User Installation Manual” before installing of the products.

Part1. Safety Warning and Attentions

For correct installation and use of this equipment, please read carefully the safety warning and

attention and strictly follow the instructions.

Basic requirements

●Do not disassemble the equipment by you. Please contact the specified maintenance department

when the equipment is out of order.

●Without authority, no company or individual are allowed to change the equipment structure,

safety and performance design.

●please obey local laws and regulations when using this product

Assembling requirements:

1. Before the assembly of the wind generator or in the process of maintenance, please be sure to

read the users manual first.

2. Please don’t install the wind turbines in rainy days or when the wind scale is at Level 3 or

above.

3. After opening the package, it is advised to short circuit the three leads of the wind turbines

the

exposed copper parts should be screwed together).

4. Before the installation of the wind turbine, lightning grounding must be prepared. You can

arrange the facilities according to national standards, or you may arrange them according to the

local environment and soil condition. Table 1 is for reference.

Summary of Contents for 2205












Reviews: