background image

X4

Chapter 1 Description

1.1 Content and Purpose

The following content points out potentially dangerous situations, please read

these instructions carefully and take necessary precautions. The essence of this

machine operating manual is to prevent injuries, and most accidents are caused at

work by not heeding basic safety rules. A careful and careful user is the best

guarantee against accidents, even stronger than some other precautions. When using

the machine, be sure to pay attention to your surroundings and people nearby,

especially children.

1.2 General Instructions

●Before any maintenance and repair, please turn the start switch to the off

position, and please remove the key from the main power switch.

●The machine must be used by qualified and authorized personnel. Children and

disabled persons are not allowed to use the machine.

●Keep the battery away from sparks, flames and smoke.

●Do not use it in a place where dangerous, flammable or explosive gas, liquid or

water vapor is present.

●This machine can clean general garbage. It is strictly forbidden to clean silk

ropes, belts, high-temperature sundries, accumulated water, flammable or toxic and

harmful substances, so as to avoid entanglement, burning the main brush and side

brush, and making them unable to work normally.

●Please keep loose clothing, hair, fingers and other body parts away from the

machine's air vents and any moving parts.

●When the machine stops, remember to turn off the power.

●Do not use the machine where the inclination exceeds the rated value of the

machine.

●Please do not smoke while charging the battery.

●Do not use the machine in a very dirty area. If the road garbage is thick, please

repeat the sweeping work twice or more.

●The machine should be in temperature between -10

to 40

.

●When using the machine, the temperature should be between -10°C and 40°C,

and the humidity should be between 30% and 95%.

●Do not use the machine as a means of transportation.

●When the machine is not moving forward, do not let the brush continue to rotate

to avoid damage to the ground.

●In case of fire, please remember to use powder fire extinguisher instead of

water.

●When the machine operation fails, make sure that the failure is not caused by

lack of regular maintenance.

●If some parts need to be replaced, you can buy spare parts from the original

manufacturer or authorized dealer.

Summary of Contents for X4


















Reviews: