YANGZI X4 Operating Instruction Download

Page: 13 / 17

3. Use the M4 Allen wrench to loosen the fixing screws of the controller and the

iron plate to remove it.

(Note: When installing, the positive and negative wiring cannot be wrongly

connected)

Disassembly and assembly of the second-generation self-propelled controller:

1. Turn off the main power supply to ensure that after the machine is powered off,

the sewage is drained and the sewage tank is turned over.

2. Remove the handle iron plate fixing screws.

3. Loosen the positive and negative wiring of the power supply, and drive the

positive and negative wiring of the motor.

4. Use the M4 Allen wrench to loosen the fixing screws of the controller and the iron

plate to complete the removal.

(Note: When installing, the positive and negative wiring cannot be wrongly

connected)

3.7 Filter maintenance and removal

Chapter 4 Analysis Table of Common

Problems of Floor Scrubber

Summary of Contents for X4


















Search results

Summary of Contents for X4

Reviews:

Related manuals for X4

Brands by name

Popular brands

YANGZI X4, Operating Instruction

Search results

Summary of Contents for X4

Reviews:

Related manuals for X4

Brands by name

Popular brands