background image

X4

1

Chapter 2 Instruction

2.1 Buttons/Panels of the Machine

Center control panel A

Center control panel B

2.1.1 The core control keys of the machine

●Power/Voltmeter (The display device can display the current battery voltage,

please charge when the voltage is lower than 21V)

●Power switch (start this switch, the device is powered on)

●Water suction button (start this button, the suction motor starts to work)

●Brushing button (start this button, the brushing motor starts to work)

●Remove the flashing button (start this button, you can remove the flashing disk)

●Forward and backward switch (start this button to control the machine to move

forward or backward)

Speed control switch (press the tortoise button, the machine runs at low speed;

press the rabbit button, the machine runs at high speed)

2.1.2 Charging the battery

●The charging socket cable requires at least a power cable with a diameter of

4mm.

●Note: The charger is placed on a stable platform, and pay attention to

moisture-proof, waterproof and drop-proof.

●The charging time must be guaranteed for 6-10 hours per charge. Make sure

the battery is fully charged when working.

●During the transportation of the charger, please do not carry the power cord by

hand to avoid loosening the terminals.

2.1.3 Adding water to the water tank

Summary of Contents for X4


















Reviews: