background image

 

 

9

GENERAL WARNINGS 

Operator must read and understand all safety and warning information, operating instructions, maintenance 

and storage instructions before operating this equipment. Failure to properly operate and maintain the lawn 

roller could result in serious injury to the operator or bystanders. 

 

Operation Warnings 

  Do not at any time carry passengers sitting or standing on the lawn roller.   

  Do not allow children to play on, stand upon or climb on the spreader. 

  Do not exceed rated capacity of 80lb   

  Replace or repair damaged or worn parts immediately. 

  To avoid personal injury and/or equipment damage DO NOT EXCEED 5 MPH. 

  Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). 

  Always inspect the spreader before using to assure it is in good working condition. 

  Always keep hands and feet clear from moving parts while operating the equipment. 

 

DO NOT

 use if the spreader is damaged or worn as this may cause injury to the operator or bystanders. 

 

ALWAYS

 make sure the spreader is secure and locked to the hitch of the approved vehicle before 

operating. 

 

Never 

add material to the spreader unless it is attached to the tractor. 

 

 

 

 

MAINTENANCE 

 

After each use clean material out of hopper. 

 

Rinse/dry inside and outside of the spreader after each use. 

 

Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE. 

 

Periodically check all fasteners for tightness. 

 

Annually clean and lightly lubricate parts. 

 

Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces. 

 

Never exceed load capacity rating of 80lbs it will damage the spreader. 

 

IMPORTANT: 

If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement parts 

that do not meet specifications may result in a safety hazard or poor operations. 

 

STORAGE 

 

Never allow material to remain in the hopper for extended periods of time. 

 

Before storing make sure the spreader is clean and dry for years of trouble free service. 

 

Store indoors or protected area during severe weather and winter months. 

 

WARNING 

ALWAYS 

maintain the proper tire pressure.   

DO NOT

 over or under inflate the tires as serious 

injury may result.   

ALWAYS

 keep the tires at 

25PSI.

 

Maintenance and Storage

Summary of Contents for YTL31507













Reviews: