background image

14

15

Lightning Protection

In order to prevent lightning damage to the machine, do 
not place the charging station under tall trees.

Operating the machine:

WARNING! This machine can cause serious injuries. 

Follow instructions below to reduce risk of accident 

and injury.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

 

Preparation:
•  Read the instructions carefully and make sure you 

understand them fully. Be familiar with the controls 

and the proper use of the machine.

•  Never allow children, persons with reduced physical, 

sensory or mental capabilities or lack of experience 

and knowledge or people unfamiliar with these 

instructions use the machine.

•  Local regulations may restrict the age of the operator. 

Children should be supervised to ensure that they do 

not play with the appliance.

•  The operator or user is responsible for accidents or 

hazards occurring to other people or their property.

•  Ensure the correct installation of the perimeter 

boundary system as instructed.

•  Periodically inspect the  area where the machine 

is to be used and remove all stones, sticks, wires, 

and other debris which could cause damage to the 

machine or be unsafe.

•  Periodically visually inspect to see that the blades, 

blade bolts and cutter assembly are not worn or 

damaged. Replace worn or damaged blades and bolts 

in sets to preserve balance.

•  On multi-spindle machines, take care as rotating one 

blade can cause other blades to rotate.

•  Never leave the machine to operate unattended, 

especially while other people such as children and 

pets are in the area.

•  Never use the machine to level out uneven patches.

SAFETY PRECAUTIONS

SAFETY PRECAUTIONS

Summary of Contents for ROBOMOWER SA800PRO


































Reviews: