120v
LITHIUM-ION
TM
14
15
ADJUSTMENT
WARNING:
Never operate the cutting
height adjustment handle roughly. Switch off the
tool and make sure that the blade has stopped
completely.
Adjust the cutting height
The cutting height is centrally adjusted by the
cutting height adjustment handle.
Different cutting heights can be selected as
follows:
1. Pull the adjusting handle outwards. (See Fig.
15)
2. Move it forwards or backwards to select the
desired cutting height.
3. Return adjusting handle back into plate.
Make sure the lever is secured in position.
From position 1 to position 7, the cutting
height ranges from 1.25 " to 4 ".
Adjust the self-propelled speed
This lawn mower features a self-propelled
function. The self-propelled speed also can be
changed by pushing the speed adjustment lever
forwards and backwards. It has 5 speeds for your
option, from 1.75 MPH to 3 MPH, the lever can
be stopped at the lever can be stopped at the
speed position desired for each operator. (See
Fig. 14)
OPERATION
To insert the battery pack
1. Open the battery pack cover and hold it in
place. (See Fig. 16)
2. Align the groove on the battery pack with the
corresponding ribs in the receptacle of the
device.
3. Depress the battery pack with moderate force
until it was locked in place (Make sure that
the battery handle is folded down).
4. Repeat the above procedure to assemble the
2nd battery pack.
5. Close the cover.
WARNING:
Make sure that the tool is
“POWER OFF”.
NOTE:
The tool can also work normally with only
one battery pack.
Battery Pack Y0L120BAT2.5 (See Fig. 26)
①
Lift handle
②
Main housing
③
Indicator button
④
Green LED lamps
⑤
Red LED lamp
Battery Pack Operation (See Fig. 27)
1. When you push the power indicator button,
the green LED lights will show the power
remaining. (see Fig. 27
①
)
2. When the battery pack over discharges or
remains very low power, the red LED light will
flash. (see Fig. 2
②
)
3. When the battery pack temperature is
exceeded, the red LED light will flash. Cool it
down for 10~20 minutes. (see Fig. 27
②
)
4. When there is fault with the battery pack, the
red LED light will flash. (see Fig. 2
②
)
5. Once the battery pack is correctly located
in the charger, the 4 green LED lights of the
battery pack will flash LED lights to indicate
the charging process. At the same time the
green LED light of the charger will flash
continuously during normal charging, while
the red LED light is still on. (see Fig. 27
③
)
To remove the battery pack from the tool
1. Open the battery pack cover and hold it in
place.
2. Press the battery pack release button, the
battery pack will spring out automatically.
（
See Fig. 17
）
3. Lift up the carrying handle and remove the
battery pack.
Safety Key
The machine is fitted with a safety ke , this
prevents the accidental start up of your cordless
lawnmower.
The safety key has been designed to totally
disable the lawnmower when the key is removed.
(See Fig. 18)
If the safety key is lost or broken, please call the
Yard Force service hot-line at 866-902-9690.
To Switch ON:
1. Depress the center of the power ON/OFF
button and hold down for 2 seconds- The
green LED light will be ON.This means the
tool is powered on normally. (See Fig. 19
)
2. Depress the safety lock button and keep
it in place. Whilst pulling the blade-Stop/
Start lever towards the handle and hold it in
position. The motor will start to work, blade
will rotate. Then release the safety lock
button. (See Fig. 20
)
3. During the normal operation, once the
capacity of battery pack becomes low, the
LED light of Power ON/OFF button will turn
red.
Battery Packs Transfer.
If there are two battery packs installed, one
of the battery packs will automatically be
powered OFF. The mower will work until
the red LED light flashes and the tool stops
working automatically. In this case, release
the blade Stop/Start lever, the power supply
will be automatically switched over to the
other battery pack. The LED light for power
ON/OFF button will turn green again. Then
operate the mower as per step 2.
CAUTION!
1. Do not start the motor in tall grass.
2. Before starting the lawn mower, ensure
that the battery pack and safety key are
correctly installed in place.
3. Before operating the lawn mower, remove
stones, loose pieces of wood and other
objects from the cutting area.
To Switch OFF:
1. Release the blade-Stop/Start lever.
2. Depress the center point of power ON/OFF
button, and hold it in place for 2 seconds. The
LED light will turn RED. Release the power
button. The red LED light will flash three
times then turn off
3. When mower is powered ON but there is
no operation for 3 minutes, the LED light of
power button will flash for 3 seconds then the
mower will be powered off automaticall .
WARNING:
The blade will continue to rotate for 3-5 seconds
after the mower has been switched off
Use the Self-propelled function
This unit is equipped with self-propelled system.
The self-propelled function can be used
independently and together with the cutting
blade operating, it is not dependent on the blade
rotation.
Use self-propelled function without blade
rotation
1. Turn the power ON/OFF button ON.
2. Push the self-propelled switch lever towards
the handle and hold it in position. The lawn
mower will start to move automatically.
(
See
Fig. 21
)
To adjust the speed, please refer to “Adjusting
the self-propelled speed” section. (See Fig.
14
)
3. To stop the moving lawn mower, just release
the self-propelled switch lever.
Use self-propelled function with the blade for
cutting
1. Start the mower as previously mentioned.
2. While holding the blade-Stop/Start lever
with one hand, then also engage the self-
propelled switch lever and the machine will
then start to move automatically.
3. Adjust the self-propelled speed-adjustment
lever to the desired driving speed.
Operate the lawn mower
Operation on a slope:
Slopes are a major factor related to slip-and-fall
accidents, which can result in severe injury.
WARNING:
Always be sure of your footing
on slopes. Operation on slopes requires extra
caution. If you feel uneasy on a slope, do not
mow it.
DO:
- Mow across the face of slopes; never mow
up and down. Exercise extreme caution when
changing direction on slopes.
- Watch for holes, ruts, rocks, hidden objects,
or bumps which can cause you to slip or trip.
Tall grass can hide obstacles.
DO NOT:
- Do not mow near drop-offs, ditches or
embankments; you could lose your footing or
balance.
- Do not mow slopes greater than 15 degrees.
- Do not mow on wet grass. Unstable footing
could cause slipping.
Mower overload protection
To prevent overload conditions, do not try to cut
too much grass at one time. Slow down your
cutting pace or raise the cut height. Your mower
has built-in overload circuit protection. When the
mower is overloaded, the motor will stop. switch
