background image

7

Starter Handle (Not Shown)

The starter handle is located on the engine. Pull the 
starter handle to start engine. 

Engine Controls

See the separate engine manual for the location and 
function of the controls on the engine.

Figure 5

SECTION 4:  OPERATING YOUR CHIPPER SHREDDER VACUUM 

WARNING: Read, understand, and follow
all instructions and warnings on the
machine and in this manual before
operating. 

Always wear the safety glasses provided 
with this machine during operation or 
while performing any adjustments or 
repairs. Thrown objects which ricochet 
can cause serious injury to the eyes. 

Gas And Oil Fill-Up

Service the engine with gasoline and oil as instructed in 
the separate engine manual packed with your chipper 
shredder vacuum. Read instructions carefully.

WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other
sources of ignition.

NOTE: See your engine manual packed with your unit
for more detailed instructions.

Starting Engine

Attach spark plug wire to spark plug. Make certain 
the metal cap on the end of the spark plug is 
fastened securely over the metal tip on the spark 
plug.

Make certain drive clutch control is in the 
disengaged (released) position.

Engines with choke lever:
Move choke lever on engine to CHOKE position. (A 
warm engine may not require choking).

Engines with primer:
Prime engine as instructed in separate engine 
manual.

The throttle control lever is located on the engine. 
Move engine throttle control lever to FAST or 
START position.

Place one foot on the left rear wheel to prevent the 
unit from skidding while starting.

Grasp starter handle and pull rope out slowly until 
engine reaches start of compression cycle (rope 
will pull slightly harder at this point).

NOTE:  A noise will be heard when at the start of the
compression cycle. This noise should be expected until
the impeller reaches full speed.   

Drive Clutch
Control

Bag

Nozzle

Nozzle Door
Adjustment Lever 

Chipper
Chute

Caster Lock

Summary of Contents for 203





















Reviews: