background image

Do not stand directly behind tiller.

Rapid retraction of the starter cord (kickback) will pull your 
handand arm toward the engine faster than you can let go. 
Broken bones, fractures, bruises, or sprains could result.

4.     Pull the recoil starter until the engine starts. Return the recoil 

to the home position after each pull. Repeat the steps as 
needed. Once engine has started, set the throttle to the FAST 
position before you operate the unit.

TINE OPERATION - SHIFT LEVER

•     Always release drive control bar before moving shift lever into 

another position.

•     Tine movement is achieved by moving shift lever to either the 

counter rotating till position ( 

 ) or the forward rotating 

till position ( 

 ) and engaging drive control bar.

FORWARD - WHEELS ONLY/TINES STOPPED

•     Release drive control bar and move shift lever indicator to 

“F”  (forward)  position.  Engage  drive  control  bar  and  tiller 
will move forward.

REVERSE - WHEELS ONLY/TINES STOPPED

•     Release the drive control bar.

•     Move throttle control to “SLOW” position.

•     Move shift lever indicator to “R” (reverse) position.

•     Hold drive control bar against the handle and tiller will move backward.

If you find the shift lever difficult to move or find it hard to shift 
gears, try one of the following: 

•     Briefly engage the drive control bar, and release, or

•     Rock the tiller forward and backward using the handles

DEPTH STAKE

The depth stake (see 

Figure 7

) can be raised or lowered to allow 

you more versatile tilling and cultivating, or to more easily 
transport your tiller.

Figure 7

Limiter

Depth Stake Pin Lever

Deepest Tilling

Shallowest Tilling

Transport Position

DRAG BAR

The drag stake (see 

Figure 8

) should be raised when tilling in the 

counter rotating ( 

 ) till position. The drag stake should be 

lowered when tilling in the forward rotating ( 

 ) till position.

TILLING

Tilling is digging in, turning over and breaking up garden soil and 
prepare a seedbed for planting. Best tilling depth is 4” (100mm) to 
6” (150mm). A tiller will also clear the soil of unwanted vegetation.
The decomposition of this vegetation matter enriches the soil.

Avoid tilling soil that is too dry as it will pulverize and produce a 
dust that will not hold water. Water a few days before tilling.  Also, 
tilling soil that is too wet will produce unsatisfactory clods. Wait a 
day or two after heavy rain for the soil to dry.

better growth will be obtained if an area is tilled properly and 
used soon after tilling to preserve the moisture content.

Lowered Position

Raised Position

Figure 8

Drag Bar Pin Lever

3.     Move  the  throttle  control 

lever slightly forward to about 
¼ of the way (slightly toward 
the fast position).

Throttle Control Lever

13

YT4565PM02 - 1704

|

   Operation

32850US25M102.indd   13

2017/3/27   10:22:06

Summary of Contents for YT4565

























Reviews: