background image

12

6.   Align and screw the collar onto the thread of the suction inlet (8) port of the  

pump (Fig. 5).

Note:

 Ensure the collar is tightly fastened onto the suction inlet (8); failure to do so 

may result in an air leak.

Discharge Outlet
Connecting Hose or Pipe to the Discharge outlet (not included)
Note: 

Keep all hoses short and as straight as possible, failure to do so may decrease the pumps performance.

Caution: 

All connections must be air tight, failure to do so may result in an air leak which can prevent the pump 

from priming. It is recommended that a thread sealant (not included) and/or Teflon tape (not included) is used on 
threads to ensure a water tight seal and prevent any leakage.
1.   Insert a hose adapter (24) into one of the collars (22).

Note:

 Ensure that an o-ring (21) is fitted into the collar (22) (Fig. 6), failure to do so 

may result in an air leak.
2.   Add thread sealant (not included) and/or Teflon tape (not included) on to the 

discharge outlet (9).

3.  Align and screw the collar onto the thread of the discharge outlet (9) port of the 

pump (Fig. 7).

Note:

 Ensure the collar is tightly fastened onto the discharge outlet (9); failure to do so 

may result in an air leak.

Priming

Priming the pump prepares the motor for safe operation.

Caution:

 Do not run the pump dry, this may result in damage to the pump.

1.   Unscrew the priming cap (11) by turning anti-clockwise. Using a hose, fill the pump 

by pouring water into the priming plug hole (Fig. 8).

2.   Ensure that the pump and suction line are full.
3.   Replace the priming cap (11) and ensure it is secure.
4.   Fully open any shut off mechanisms (eg: spray nozzle, valves etc.) in the input and output hose or pipe so that 

the air can escape without obstruction.

SETUP & INSTALLATION (cont.)

Fig. 5

Fig. 7

Fig. 8

Fig. 6

Summary of Contents for YW20PTP



















Reviews: