5.7 Vibration Suppression Function (Fn205)
5-49
5
Adjustments
(2) Operating Procedure
Step
Display after Operation
Keys
Operation
1
Input a control reference and take the following steps while repeating positioning.
2
Press the
Key to view the main menu for the
utility function mode.
Use the
or
Key to move through the list,
select Fn205.
3
Press the
Key. The display shown on the left will
appear.
Measure f: Measurement frequency
Setting f: Setting frequency [Factory-set to the set
value for Pn145]
Notes:
• If the setting frequency and actual operating fre-
quency are different, “Setting” will blink.
The detected vibration frequency will be displayed.
• Frequency detection will not be performed if there
is no vibration or the vibration frequency is outside
the range of detectable frequencies. The following
screen will be displayed if vibration is not detected.
If the vibration frequencies are not detected, pre-
pare a means of detecting and measuring the vibra-
tion. When the vibration frequencies are measured,
go to step 5 and manually set the measured vibra-
tion frequency.
4
Press the
Key. The displayed “Measure f” value
will be displayed as the “Setting f” value as well
.
Waveform
5
If the vibration is not completely suppressed, press
the
or
Key to move the cursor, and press
the
or
Key to fine-tune the frequency. Skip
this step and go to step 7 if the fine-tuning of the fre-
quency is not necessary.
Note:
If the setting frequency and actual operating fre-
quency are different, “Setting” will blink.
㧾㨁㧺 ̆㧲㨁㧺㧯㨀㧵㧻㧺̆
㧲㨚㧞㧜㧠㧦㧭㧙㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧡㧦㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧢㧦㧱㨍㨟㨥ޓ㧲㧲㨀
㧲㨚㧞㧜㧣㧦㨂㧙㧹㨛㨚㨕㨠㨛㨞
㧾㨁㧺 ̆㨂㨕㨎 㧿㨡㨜̆
㧹㨑㨍㨟㨡㨞㨑 㨒㧩㧙㧙㧙㧙㧙㧴㨦
㧿㨑㨠㨠㨕㨚㨓 㨒㧩㧜㧡㧜㧚㧜㧴㨦
㧾㨁㧺 ̆㨂㨕㨎 㧿㨡㨜̆
㧹㨑㨍㨟㨡㨞㨑 㨒㧩㧜㧝㧜㧚㧠㧴㨦
㧿㨑㨠㨠㨕㨚㨓 㨒㧩㧜㧡㧜㧚㧜㧴㨦
㧾㨁㧺 ̆㨂㨕㨎 㧿㨡㨜̆
㧹㨑㨍㨟㨡㨞㨑㨒 㧩㧙㧙㧙㧙㧙㧴㨦
㧿㨑㨠㨠㨕㨚㨓㨒 㧩㧜㧡㧜㧚㧜㧴㨦
㧾㨁㧺 ̆㨂㨕㨎 㧿㨡㨜̆
㧹㨑㨍㨟㨡㨞㨑 㨒㧩㧜㧝㧜㧚㧠㧴㨦
㧿㨑㨠㨠㨕㨚㨓 㨒㧩㧜㧝㧜㧚㧠㧴㨦
Error
Force
reference
㧾㨁㧺 ̆㨂㨕㨎 㧿㨡㨜̆
㧹㨑㨍㨟㨡㨞㨑 㨒㧩㧜㧝㧜㧚㧠㧴㨦
㧿㨑㨠㨠㨕㨚㨓 㨒㧩㧜㧝㧞㧚㧠㧴㨦
