background image

General

1.1  Copyright 

©

 VIPA GmbH

This document contains proprietary information of VIPA and is not to be disclosed or used

except in accordance with applicable agreements.

This material is protected by the copyright laws. It may not be reproduced, distributed, or

altered in any fashion by any entity (either internal or external to VIPA), except in accord-

ance with applicable agreements, contracts or licensing, without the express written con-

sent of VIPA and the business management owner of the material.

For permission to reproduce or distribute, please contact: VIPA, Gesellschaft für Visuali-

sierung und Prozessautomatisierung mbH Ohmstraße 4, D-91074 Herzogenaurach, Ger-

many

Tel.: +49 9132 744 -0

Fax.: +49 9132 744-1864

EMail: info@vipa.de

http://www.vipa.com

Every effort has been made to ensure that the information contained in

this document was complete and accurate at the time of publishing. Nev-

ertheless, the authors retain the right to modify the information.

This customer document describes all the hardware units and functions

known at the present time. Descriptions may be included for units which

are not present at the customer site. The exact scope of delivery is

described in the respective purchase contract.

Hereby, VIPA GmbH declares that the products and systems are in compliance with the

essential requirements and other relevant provisions. Conformity is indicated by the CE

marking affixed to the product.

For more information regarding CE marking and Declaration of Conformity (DoC), please

contact your local VIPA customer service organization.

VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V,

System 500S and Commander Compact are registered trademarks of VIPA Gesellschaft

für Visualisierung und Prozessautomatisierung mbH.

SPEED7 is a registered trademark of profichip GmbH.

SIMATIC, STEP, SINEC, TIA Portal, S7-300 and S7-400 are registered trademarks of

Siemens AG.

Microsoft and Windows are registered trademarks of Microsoft Inc., USA.

Portable Document Format (PDF) and Postscript are registered trademarks of Adobe

Systems, Inc.

All other trademarks, logos and service or product marks specified herein are owned by

their respective companies.

Contact your local VIPA Customer Service Organization representative if you wish to

report errors or questions regarding the contents of this document. If you are unable to

locate a customer service centre, contact VIPA as follows:

All Rights Reserved

CE Conformity Declaration

Conformity Information

Trademarks

Information product sup-

port

VIPA HMI

General

Copyright 

©

 VIPA GmbH  

HB160 | TP-smart | H41-71A41-0 | en | 18-04

 

4

Summary of Contents for TP304-SM












































Reviews: