background image

4.2  Settings on Welding Source Panel

4-4

HW0480311

HW0480311

4.2

Settings on Welding Source Panel 

4.2.1

Changing Welding Type

The following describes how to change the welding type.

(1) Press the button 

 "Weld. Type", and the 7-segment LED indicator 

f

 "Type" 

blinks.

(2) Use the button 

 "+" or "-" to increase or decrease the value.  Use the button 

 "L" 

or "R" to move the digit.

(3) After changing the value, press the button 

 "Weld. Type" or leave it without doing 

anything for 10 seconds, and the 7-segment LED indicator 

f

 "Type" lights.

Press the button 

 "Record" for 3 seconds or more to save the changed value.  Do 

not turn OFF the welding source while pressing this button.  The saving of condi-
tions is completed when the 7-segment LED indicators are lit again.  

The welding types available for software version 3.20-000-6 (CPU) are listed on the 
nameplate attached to the front panel of the welding source.

Welding types other than listed on the nameplate are not available.  Using improper 
welding type will result in unstable welding, which causes excessive spatters or 
imperfect bead appearance.  Before starting welding, confirm that the welding type 
has been correctly selected.

12

V

A

Wire m/min

Type

13

13

12

V

A

Wire m/min

Type

14

38/129

Summary of Contents for YWE-EH500-6N0


































































































































Reviews: