YATO YT-07195, Manual

10

O R I G I N A L   I N S T R U C T I O N S

EN

Hazards related to repetitive movements 

When using a pneumatic tool for work entailing repetitive movements, the operator is exposed to the discomfort of hands, arms, 

shoulders, neck, or other parts of the body. When using a pneumatic tool, the operator should take a comfortable posture to en-

sure the feet are correctly positioned and avoid strange or unbalanced postures. The operator should change the posture over a 

long time to avoid discomfort and fatigue. If the operator experiences symptoms such as persistent or repeated discomfort, pain, 

pulsating pain, tingling, numbness, burning, or sti

ff

 ness, they should not ignore them. The operator should inform the employer 

and consult a physician. 

Hazards connected with accessories

Disconnect the tool from the power supply before replacing the tool to be inserted or accessory. Use accessories and consum-

ables only in the sizes and types recommended by the manufacturer. Do not use cracked or deformed accessories. Check the 

condition of the accessories prior to each use. 

Hazards connected with the workplace 

Slips, stumbles, and falls are the main causes of injury. Beware of slippery surfaces caused by using the tool, as well as tripping 

hazards caused by the air system. Proceed with caution in an unfamiliar environment. Hidden hazards may exist, such as electricity 

or other utility lines. The pneumatic tool is not intended for use in potentially explosive zones and is not insulated from contact with 

electricity. Make sure that there are no electric cables, gas pipes, etc. which could pose a risk in the case of damage with the tool.     

Noise hazard 

Exposure to high levels of noise can cause permanent and irreversible hearing loss and other problems such as tinnitus (ringing, 

buzzing, whistling or buzzing in ears). A risk assessment and the implementation of appropriate control measures for these haz-

ards are necessary. Use hearing protection in accordance with the employer’s instructions and in accordance with hygiene and 

safety requirements. The operation and maintenance of the pneumatic tool must be carried out in accordance with the instructions 

in the instructions manual in order to avoid an unnecessary increase in noise levels. Selection, maintenance, and replacement of 

consumables/inserted tools must be carried out in accordance with the instructions in the manual in order to prevent an unneces-

sary increase in noise levels. If the pneumatic tool has a silencer, always make sure that it is installed correctly when using the tool. 

Additional safety instructions for pneumatic tools 

The pressurised air can cause serious injuries:

- always disconnect the air supply, release the air pressure from the hose, and disconnect the tool from the air supply when not in 

use, before changing accessories, or carrying out repairs;

- never point the air stream at yourself or anyone else.

Hitting with the hose can cause serious injuries. Always check for damaged or loose hoses and connectors. Direct cold air away 

from hands. Whenever universal screwed connections (dog connections) are used, safety pins and safety connectors must be 

used to prevent damage to the connections between the hoses and between the hose and the tool. Do not exceed the maximum 

air pressure speci

fi

 ed for the tool. Never carry the tool holding it by the hose.

OPERATING CONDITIONS 

The oil dispenser may only be used for the distribution and temporary storage of engine oil, transmission oil, etc. from vehicles 

and other machines equipped with a combustion engine. The product is not intended for distribution and temporary storage of 

fl

 ammable liquids, e.g., petrol, solvents, diesel, alcohol, etc. and corrosive liquids, e.g., brake 

fl

 uid.

Make sure that the compressed air source generates the correct working pressure and provides the required air 

fl

 ow. If the supply 

air pressure is too high, a pressure regulator with a safety valve must be used. Applying too high a pressure can lead to rupture 

of the product components, which can cause serious injuries. 

The pneumatic tool must be fed through the 

fi

 lter and lubricator system. This will ensure that the air is both clean and moistened 

with oil. Check the condition of the 

fi

 lter and lubricator before each use and clean the 

fi

 lter if necessary or make up for the oil 

shortage in the lubricator. This will ensure the correct operation of the tool and extend its service life. 

In the case of heavy loads, a recoil force may be generated towards the tool operator. It is necessary to adopt such a posture 

during work to be able to counteract these forces e

ff

 ectively. 

Always make sure that all wrenches and tools used for adjusting are removed before starting work.

Always use protective goggles when adjusting and using the product. 

Check the cables and adapters for leaks before each use. 

Before connecting to the compressed air source, make sure that all valves and switches are in the “OFF” position.

Do not exceed the maximum supply air pressure.

Never exceed the temperature range of the oil to be distributed. Excessive heat can damage the plastic parts of the product and 

cause serious burns.  

Do not use this equipment for applications not listed in the manual. Distribution of 

fl

 uids other than those speci

fi

 ed in the instruc-

tions manual may cause injuries and 

fi

 re, as well as damage to the product. 

During oil distribution, the machine that is being 

fi

 lled with oil must not move.