19
O R I G I N A L I N S T R U C T I O N S
EN
described in the section describing the cover dismantling. Check that the drive cover is correctly
fi
tted and that all cover clips are
correctly locked. If it is found that there is a need to replace the drive belt, contact the manufacturer’s authorised service centre.
Cleaning the air
fi
lter
The air
fi
lter prevents dust and dirt from being drawn into the compressor. The air
fi
lter becomes dirty, depending on the condi-
tions and operation time of the compressor. Check the soiling status of the
fi
lter once a month and, if it needs cleaning, clean or
replace the
fi
lter at least every 50 hours of the compressor operation. A clogged inlet
fi
lter can severely limit the compressor’s
performance and damage the device. It is forbidden to use the compressor without a correctly
fi
tted air
fi
lter. Contaminants that
enter the compressor with the air can damage it.
In the devices with the catalogue numbers YT-23300 and YT-23305, unscrew the
fi
lter by hand counterclockwise, remove the
fi
xing screw from the air
fi
lter housing (XIII), open the housing, and pull the
fi
lter out of the housing. Clean the
fi
lter in a soapy water
solution, rinse in water, and dry thoroughly. Place the
fi
lter in the housing, assemble the two parts of the housing, and screw in the
fi
xing screw. Screw the air
fi
lter clockwise by hand into the air
fi
lter opening. Ensure that the air
fi
lter is
fi
tted correctly.
In the devices with the catalogue numbers YT-23310 and YT-23320, remove the air
fi
lter from the compressor body using a span-
ner by unscrewing the
fi
xing screws (XIV). Open the housing and pull the
fi
lter out of the housing. Clean the
fi
lter in a soapy water
solution, rinse in water, and dry thoroughly. Place the
fi
lter in the housing, assemble the two parts of the housing, and fasten the
air
fi
lter to the compressor body with screws. Ensure that the air
fi
lter is
fi
tted correctly.
STORAGE AND TRANSPORT
Transport the device by grasping it by the handle or the base. In the case of transporting it by the means of transport, the com-
pressor must be secured against movement. Only transport and store the device when turned o
ff
, disconnected from the power
supply, and with the air tank empty. Store the device in closed well-ventilated rooms. During storage and transport, the device
should not be exposed to direct sunlight, heat sources and precipitation. The storage place should protect the device from access
by unauthorised persons, especially children. Do not place anything on the device.
Summary of Contents for YT-23300
