YATO YT-82130, Instructions Manual

12

GB

O R I G I N A L   I N S T R U C T I O N S

damage is detected, it is prohibited to continue working!

Attention! All actions consisting in replacement of the working tools (drill and cutter with the SDS max chuck system), installation 

of guards and guides, adjustments etc. must be carried out when the power supply voltage is disconnected: 

Remove the plug of 

the cord of the tool from the mains socket

!

Installation of SDS max working tools in the tool chuck

Clean the selected tool of dirt and rust and lubricate The SDS max chuck with a thin layer of grease. 

Tool the tool chuck towards you and maintain it in this position (IV).

Insert a clean tool in the opening. If necessary, turn the tool, so that it enters the chuck without resistance.

Release the chuck; the tool should lock automatically in the chuck.

Make sure the tool is securely installed, trying to remove it from the SDS max chuck. If the drill or the cutter can be removed from 

the chuck, the installation procedure must be repeated.

Selection of kind of operation (V)

The hammer action operation facilitates drilling in concrete, walls and hard ceramic materials (hard bricks, stones, marble). The 

hammer action selector must be set to hammer action indicated with a symbol of a drill and a hammer. 

In order to do so, set the operating mode selector to the hammer symbol.

Preparation

Select adequate tools and install them in the chuck. 

Set the operating mode selector to the adequate position: hammer symbol – hammering; hammer and drill symbol – drilling with 

hammer action; drill symbol – drilling without hammer action; hammer with an arrow – setting the position of the position of the 

chisel. 

Wear hearing and eyes protection, and protective gloves. 

Plug the cord to the mains.

Adapt a position that guarantees equilibrium, grab the hammer drill with both hands and start it pressing the electric switch (VI).

Hold the tool for a couple of minutes, so that the lubricant reaches all the elements of the drive mechanism.

Turn the hammer drill off, releasing the switch.

Attention!

 In case any suspicious sounds are detected the hammer drill must be immediately disconnected from the mains. Have 

it inspected by an authorised service point.

USING THE TOOL

Attention! While operating the hammer drill, it is required to use hearing protection! 

Drilling in ceramic materials

Drilling in hard and compact materials: concrete, hard bricks, stone, marble etc.

While the hammer drill is disconnected from the mains, install a drill in the chuck. 

Set the operating mode selector to drilling with hammer action, or if it is available, to drilling without hammer action. 

Plug the tool to the mains, turn the hammer drill on with the switch and start work.

During work make regular breaks – avoid overheating of the hammer drill and the tool.

Drilling with hammer action is recommended only in case of compact ceramic materials: concrete, hard bricks, stone etc. In case 

of drilling holes of large diameter, it is recommended to drill first a smaller guide hole, and then use a drill of the final diameter. Use 

drills designed for hammer action drilling. 

It is not recommended to use the hammer action function in case of ceramic materials of loose structure, such as: glaze, soft 

bricks, plaster, etc. Hammer action drilling in such materials may damage the material. 

The hammer drill is equipped with a clutch that prevents overloading of the electric motor in case when the tool is jammed during 

work, for example as a result of hitting a reinforcement wire. In such cases the drill will stop rotating, although the electric motor 

is still working. 

Also excessive pressure exerted on the tool during work may cause activation of the clutch. 

In such cases remove the tool from the hole, make sure the hammer drill is functioning correctly and then resume work, applying 

only the pressure which is necessary for proper operation. In case a reinforcement rod or another hidden metal obstacle is hit, 

drill it using the hammer action function and a drill for metal of the same diameter as the hammer action drill, and then continue 

drilling in the ceramic material.      

Hammering

While the tool is disconnected from the mains install the required tool in the chuck: cutter or punch.

Set the operating mode selector to the hammering position. Plug the drill to the mains, turn the hammer drill on with the switch,