61
I S T R U Z I O N I O R I G I N A L I
IT
tuazione e’, piu’ spesso, l’eccessiva densita’ dell’olio. In caso di uso del prodotto a temperatura di ambiente bassa, e’ necessario,
lasciare funzionare il martello per circa 5 minuti per consentire il suo riscaldamento.
Appoggiare l’utensile alla super
fi
cie lavorata, a
ff
errare il martello con entrambe le impugnature e avviare il motore. Se l’utensile
di lavoro non si attiva, spingere il martello verso la super
fi
cie lavorata. Non si tratta di un malfunzionamento, ma di intervento di
protezione contro il lavoro senza carico.
Durante la lavorazione, esercitare soltanto pressione necessaria per il corretto funzionamento dell’utensile. Una pressione ecces-
siva esercitata sull’utensile puo’ comportare il danneggiamento dell’utensile stesso e dei meccanismi del martello a percussione,
e la riduzione del suo rendimento.
In caso di uso del prodotto per la demolizione di una super
fi
cie di elevato spessore, eseguire demolizione a strati, ovvero demolire
alla volta uno strato di spessore
fi
ne.
Durante la lavorazione, praticare intervalli regolari.
Note aggiuntive
Durante la lavorazione, non esercitare pressione eccessiva sul materiale lavorato, e non eseguire movimento bruschi, per evitare
il danneggiamento dell’utensile e del trapano. Fare intervalli regolari durante la lavorazione. Non sovraccaricare l’utensile, la
temperatura delle super
fi
ci esterne non deve superare mai 60
O
C. Terminata la lavorazione, spegnere il trapano, estrarre la spina
del cavo dell’elettroutensile dalla presa della corrente e procedere alla manutenzione e veri
fi
che.
Il valore totale dichiarato di vibrazioni e’ stato misurato mediante metodo di veri
fi
ca standard, e puo’ servire per far confronto di un
attrezzo all’altro. Inoltre, tale valore puo’ essere usato per la valutazione preliminare dell’esposizione.
Attenzione! L’emissione di vibrazioni durante l’uso dell’attrezzo puo’ variare rispetto al valore dichiarato in funzione delle modalita’
di uso dell’attrezzo.
Attenzione! E’ necessario de
fi
nire le misure di sicurezza atte a proteggere l’operatore, basate sulla valutazione di esposizione
a rischio nelle condizioni e
ff
ettive (incluse tutte le fasi del ciclo di lavoro, ad esempio, durata di inutilizzo dell’attrezzo, durata di
funzionamento in folle, e tempo di attivazione).
MANUTENZIONE E REVISIONI
Lubri
fi
cazione
Prima di usare le punte o i troncatori, e’ necessario pulirli e lubri
fi
care il codolo spalmando sopra un
fi
lm
fi
ne di grasso.
ATTENZIONE! Prima di eseguire i lavori di regolazione, riparazione o manutenzione, scollegare la spina dalla presa di corrente.
Una volta
fi
nito il lavoro controllare lo stato tecnico del dispositivo elettrico attraverso l’esame visivo e la valutazione dei seguenti
elementi: corpo e manico, cavo di alimentazione con spina e pressacavo, funzionamento dell’inseritore, eventuali tamponamenti
nella s
fi
nestratura del motore, scintillazione sulle spazzole, livello di rumore dei cuscinetti e del cambio, avviamento e regolarità
del funzionamento. Durante il periodo di garanzia l’utente non può smontare dispositivi elettrici, sostituire sottogruppi o compo-
nenti, sotto pena della perdita dei diritti a garanzia. Ogni malfunzionamento veri
fi
catosi durante l’esame o durante il lavoro, deve
essere riparato presso un centro di assistenza tecnica. Una volta
fi
nito il lavoro, pulire il corpo, la s
fi
nestratura del motore, i com-
mutatori, il manico supplementare e i ripari, p.e. con il
fl
usso d’aria (a pressione non superiore a 0,3 MPa), con un pennello o un
panno morbido secco, senza usare mezzi chimici o detersivi. Gli attrezzi e i mandrini vanno puliti con un panno pulito e secco.
Summary of Contents for YT-82133
