YATO YT-82140, Original Instructions Manual

13

GB

O R I G I N A L   I N S T R U C T I O N S

In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside 

closed areas.

 Using a correct extension cord permits to reduce the risk of an electric shock.

If operating a power tool in a damp location is unavoidable, use a residual current device (RDC) protected supply.

 Use of 

an RCD reduces the risk of electric shock.  

Personal safety        

Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are 

tired or under effects of medicines or alcohol.

 Even a moment’s inattention during work may lead to serious injuries. 

Always use individual means of protection. Always wear goggles.

 Using individual means of protection, such as dust-masks, 

protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries. 

Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the 

mains.

 Holding the tool with a finger on the switch or connecting an electric tool when the switch is in the ON position may lead 

to serious injuries. 

Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments.

 A 

spanner left on rotating elements of the tool may lead to serious injuries. 

Keep your balance. Maintain an appropriate position.

 It will permit to control the electric tool in case of unpredicted situations 

during its operation. 

Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving 

elements of the electric tool.

 Loose clothes, jewellery or long hair may get caught on moving elements of the tool. 

Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected.

 Using of 

dust extractors permits to reduce the risk of serious injuries. 

Operation of the electric tool

Do not overload the electric tool. Use a proper tool for the given purpose.

 A correct selection of the tool for the given work 

will result in a more efficient and safer work. 

Do not use the electric tool if the switch is not functioning properly.

 A tool which may not be controlled by means of a switch 

is dangerous and must be repaired. 

Disconnect the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool.

 It 

will permit to avoid accidental activation of the electric tool. 

Store the tool away from children. Do not allow untrained persons to operate the tool.

 An electric tool may be dangerous 

in hands of an untrained person. 

Make sure the tool is properly maintained. Check the tool in order to detects any unfitting or loose moving elements. 

Check whether the elements of the tool are not damaged. In case any damaged elements of the tool are detected, they 

must be repaired before the electric tool is operated.

 Many accidents are caused by improper maintenance of tools. 

Cutting tools must be sharp and clean.

 Properly maintained cutting tools are easier to control during work. 

Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool in accordance with 

its purpose, taking into account the kind and conditions of work.

 Should the tool be used for other applications than the ones 

it has been designed for, the risk of a dangerous situation increases.

Repairs 

The tool may be repaired only by authorised service centres, which must use solely original spare parts.

 It will guarantee 

a proper level of safety of operation of the electric tool. 

ADDITIONAL SAFETY INSTRUCTIONS

Do not put the tool down before the knife stops. 

An exposed rotating knife may „catch” the ground and impede the control of 

the tool and cause serious injuries.

Hold the tool only by the insulated surfaces, since the cutting element may touch the power supply cable of the tool.

 If the 

cable is cut, the metal elements of the tool might become live, which might cause electric shock to the operator.

Use clamps or other elements to fix the processed element to a stable surface. 

If the processed material is held with a hand 

or another part of the body, the tool is not stable and the operator may lose control over it.   

INSTALLATION OF WORKING ELEMENTS

Attention! 

Installation of the accessories must be realised with the power supply off (Remove the plug of the cord of the grinder 

from the socket!!

Attention!

 It is always required to replace all the knives the plane is equipped with. It is prohibited to operate the tool, if not all the 

knives are installed. The drum rotates at a high velocity and it is adequately balanced for operation with all the knives installed. If 

not all the knives are installed, the plane may be damaged during operation, which may cause serious injuries.