11
GB
O R I G I N A L I N S T R U C T I O N S
SPECIFICATION OF THE PRODUCT
Grinding wheel cutter is a versatile tool, designed for cutting metal using abrasive discs. Due to its adjustment angle and square
cutting is easy. Correct, reliable, and safe operation of the tool is dependent on proper use, therefore:
Prior to working with the device, you should read all the instruction and keep it around.
For any damage caused by failure to comply with safety regulations and instructions of this manual, the supplier is not respon-
sible.
EQUIPMENT
There should be in the factory packaging:
- cutter
- grinding wheel
TECHNICAL DATA
Parameter
Unit
Value
Catalog number
YT-82180
Rated voltage
[V]
230 AC
Rated frequency
[Hz]
50
Rated power
[W]
2300
Rated revs
[min
-1
]
3800
Maximum depth of cutting
[mm]
100
Depth of cutting at 90° (square profile)
[mm]
119 x 119
Depth of cutting at 90° (rectangle profile)
[mm]
115 x 130
Depth of cutting at 90° (angle bar)
[mm]
137 x 137
Depth of cutting at 90° (round profile)
[mm]
100
Depth of cutting at 45° (square profile)
[mm]
94 x 94
Depth of cutting at 45° (rectangle profile)
[mm]
125 x 92
Depth of cutting at 45° (angle bar)
[mm]
100 x 100
Depth of cutting at 45° (round profile)
[mm]
100
grinding wheel: ext.dia. x mounting dia. x max. thickness
[mm]
355 x 25,4 x 3
Weight
[kg]
16
Noilse level
- accustic pressure L
pA
± K
[dB (A)]
110,23 ± 3,0
- power L
wA
± K
[dB(A)]
123,23 ± 3,0
Level of vibration
[m/s
2
]
2,417 ± 1,5
Insulation class
I
Degree of protection
IP20
GENERAL SAFETY CONDITIONS
ATTENTION! When there are used electric tools, you should observe the basic safety rules. This will allow to reduce the risk of
fire, electrical shock or personal injury.
Before you begin your work with the product, you should consult the manual and keep it around.
Keep work area clean. Contaminated places and tables increase risk of injury.
Take care of the work environment. Do not expose the tool for rain. Do not use the tool in a damp or wet environment. Ensure
proper lighting of the workplace. Do not use the tool in presence of flammable liquids or gases.
Protection against electric shock. Avoid body contact with grounded surfaces (such as pipes, heaters, stoves, refrigerating ma-
chines).
Keep bystanders away. Do not allow any bystanders, especially children, who are not participating in work, to touch tools or an
extension cord. All bystanders must be kept away from the place of work.
Storage of the product. Product should be stored in a dry, protected place, out of the reach of children.
Do not overload the tool. Work will be more efficient and more secure in the event of the tools usage in accordance with its
intended purpose.
Use the appropriate tool. Do not overload a small tool in the work, which is intended for high-efficiency tools. Do not apply tools in
disaccordance with the intended purpose, e.g. do not use cutters for metal to cut pieces of wood.
Summary of Contents for YT-82180
