23
O
R
I
G
I
N
A
L
A
N
L
E
I
T
U
N
G
D
Vorbereitungen vor Geräteeinsatz
Vor dem Geräteeinsatz:
Bearbeitetes Material im Schraubstock oder in Schraubzwingen befestigen.
Für die jeweilige Arbeit geeignete Werkzeuge verwenden. Dafür sorgen, dass sie entsprechend geschärft und intakt sind.
Arbeitskleidung sowie Gehör- und Augenschutz anlegen.
Akku im Produkt einbauen.
Produkt am Pistolen- und Zusatzhandgri
ff
fassen (VII).
Sichere und stabile Körperlage einnehmen.
Produkt einschalten, dazu Steuerschalter mit dem Finger drücken.
Achtung!
Werden abnormale Geräusche, Gerüche usw. festgestellt, Produkt sofort still setzen und Akku demontieren.
Der Akku-Schlagbohrer und -schrauber wird still gesetzt, indem der Steuerschalter losgelassen wird. Danach kann das Einbau-
werkzeug noch eine kurze Zeit rotieren. Erst nachdem das Einbauwerkzeug ganz still steht, kann das Produkt zur Seite gelegt
bzw. Eingri
ff
e daran vorgenommen werden.
PRODUKTEINSATZ
Rechts- bzw. Linksumdrehungen verwenden
Rechtsumdrehungen für handelsübliche rechtsgängige Spiralbohrer einstellen.
Linksumdrehungen bei im Material verklemmtem rechtsgängigem Bohrer sowie zum Schraubenentfernen einstellen.
Beim Schraubenentfernen minimale Drehzahl einsetzen.
Holz bohren
Vor dem Bohren soll das bearbeitete Material in einem Schraubstock oder mit Schraubzwingen befestigt werden, mit einem Kör-
ner oder Nagel wird die künftige Bohrung festgelegt. Richtigen Bohrer im Bohrfutter befestigen, Drehgeschwindigkeit einstellen,
Werkzeug elektrisch anschließen und Bohrung herstellen.
Bei durchgängigen Bohrungen ist es empfehlenswert, das Material mit einem Stück Holz zu unterlegen, damit die Bohrungskante
sauber hergestellt wird.
Bei groß dimensionierten Bohrungen ist es empfehlenswert, zuvor eine Pilotbohrung herzustellen.
Metall bohren
Das bearbeitete Material muss immer sicher befestigt werden.
Beim Verbohren von dünnen Blechen ist es empfehlenswert, das Material mit einem Holzstück zu unterlegen, um unerwünschte
Verformungen usw. zu verhindern. Anschließend sind künftige Bohrungen mit einem Körner anzuzeichnen und mit Bohrern für
Stahl herzustellen. Beim Verbohren von Gusseisen sollten Hartmetallbohrer eingesetzt werden. Bei groß dimensionierten Boh-
rungen ist es empfehlenswert, zuvor eine Pilotbohrung herzustellen. Beim Verbohren von Stahl ist der Bohrer mit Maschinenöl,
bei Aluminium hingegen mit Terpentin oder Para
ffi
n zu kühlen.
Beim Verbohren von Messing, Kupfer oder Gusseisen wird der Bohrer nicht gekühlt, sondern mehrmals aus dem Material her-
ausgeführt, um ihn abkühlen zu lassen.
Keramiksto
ff
e bohren
Harte, feste Materialien bohren (Beton, harte Ziegelsteine, Stein, Marmor usw.)
Zuerst eine Pilotbohrung ohne Schlagbohrfunktion herstellen. Die vorgesehene Bohrung mit Schlagbohrfunktion herstellen. Hart-
metallbohrer von guter Bescha
ff
enheit verwenden.
Fliesen, weiche Ziegelsteine, Putz usw. bohren
Wie zuvor, jedoch ohne Schlagbohrfunktion bohren.
Bohrer ab und an aus der Bohrung ziehen, um Staub und Abfälle zu entfernen. Konstanten Druck auf das Gerät beim Bohren ausüben.
Werden Bohrungen hergestellt, bei denen das Gerät mit dem Bohrfutter nach oben gerichtet ist, sollte ein separat erhältlicher
Bohrfutterschutz verwendet werden, um das Eindringen von bei der Arbeit entstehendem Staub ins Bohrfutter zu verhindern. Der
Schutz besteht aus
fl
exiblem Kunststo
ff
weist eine Ö
ff
nung zum Bohrerdurchstecken auf.
Aussparungen ausschneiden
Die Bohrmaschine kann für die Herstellung von größeren Aussparungen im Holz mit speziellen Festdurchmesserbohrern oder mit
austauschbaren Bohrkronen eingesetzt werden.
Um Grat zu vermeiden und Bohrungen mit sauberen Auslaufkanten herzustellen, ist das Material mit einem Holzstück zu unter-
legen.
Einstellen der Lage des Meißels
Einige der eingesetzten Werkzeuge, die zum Schmieden zwecks sicherer und ergonomischer Arbeit eingesetzt sind, erfordern die
Summary of Contents for YT-82770
