9
O R I G I N A L I N S T R U C T I O N S
GB
PRODUCT CHARACTERISTICS
A battery glue gun is designed for bonding di
ff
erent materials by means of hot-melt glue cartridges. Thanks to e
ffi
cient battery of high capacity it is possible
to work with the product wherever it is not possible to work with guns with external power supply. The product has not been designed for commercial appli-
cations. Correct, reliable and safe operation of the product depends on proper operation, therefore:
Before starting the work with this product, please read this manual and keep it properly.
The supplier does not assume any liability for any damages resulting from misuse of the tool, failure to follow safety regulations and recommendations spec-
i
fi
ed in this manual. Misuse of the tool will also result in loss of guarantee and warranty rights of the user.
PRODUCT ACCESSORIES
The product is supplied in a complete state and requires no assembly. Together with the product there are provided: the rechargeable battery and charging
station (charger).
TECHNICAL DATA
Parameter
Measuring unit
Value
Catalogue number
YT-82854
Operating voltage
[V d.c.]
18
Protection class
IPX0
Insulation class
III
Glue cartridge diameter
[mm]
11,2
Operating temperature
[
O
C]
200
Heating time
[s]
25
Max. operating time
[min]
60
Capacity
[g/min]
25
Weight
[kg]
0,3
Battery type
Li-Ion
Battery capacity
[Ah]
2
Charger
Input voltage:
[V~]
220 - 240
Mains frequency
[Hz]
50 / 60
Rated power
[W]
50
Input current:
[A]
0,8
Output voltage:
[V d.c.]
21,4
Output current:
[A]
2,4
Charging time
[h]
~1
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock,
fi
re or injuries. The notion of electric tool used
in the instructions applies to all the tools which are powered with electric current, both wire tools and wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not work with electric tools in explosive environments, or those which contain in
fl
ammable liquids, gases or vapours.
Electric tools generate
sparks, which may cause a
fi
re in case of contact with in
fl
ammable gases or vapours.
Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must
fi
t the mains socket. Do not modify the plug. Do not use any adapters whatsoever in order to adapt the
plug to the socket.
Unmodi
fi
ed plug which
fi
ts the socket reduces the risk of an electric shock.
Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators.
Grounding of the body increases the risk of an electric shock.
Do not expose electric tools to precipitation or humidity.
Water and humidity which gets into the electric tool increases the risk of an electric shock.
Do not overload the power supply cable. Do not use the power supply cable in order to carry the tool or to connect and disconnect the plug from
Summary of Contents for YT-82854
